Abstract:Vibrating wire technique is a promising measurement method for small-aperture Permanent Magnet Quadrupoles (PMQs) in linear accelerators and scanning nuclear microprobes. In this paper, we describe the improved vibrating wire setup for measuring an individual PMQ with the minimum aperture of several millimeters. This setup is aiming at measuring the magnetic center. The advantage of this setup is that any mechanical measurement on the wire, which may be the main error source, is avoided. Experiments of the 20 mm-aperture Halbachtype PMQs for Xi’an Proton Application Facility (XiPAF) DTL has been carried out. The research results of the magnetic center measurements show a precision of about 10 μm and robustness against the background magnetic field. Results of the magnetic center and field multipoles measurements agree with the ones obtained from the rotating coil. INTRODUCTION The 325 MHz Alvarez DTL for the Xi’an Proton Application Facility (XiPAF) will be used to accelerate the Hbeam from 3 to 7 MeV. As shown in Figure 1, the 20 mm-aperture Halbach-type Permanent Magnet Quadrupoles (PMQs) are used in the DTL. The tolerance for the PMQs are list in Table 1. The measurement of the magnetic center is very important. The misalignment of the magnetic center will cause the beam to deviate. Rotating coil is the conventional method to achieve the magnetic center position as well as the multipole contents of the quadrupoles. However, it is difficult to measure the magnets with small apertures of several millimeters. To achieve high efficiency, the apertures of the magnets has been smaller and smaller in new linear accelerators. A new measuring method which is free from the restriction of the aperture should be developed. Vibrating wire method is a high accuracy method adapt for measuring the magnetic center of the small-aperture magnets. This method is quite sensitive to make the wire coincides with the magnetic center. However, it is difficult to relate the wire to external fiducials. The improved fiducialization method is described in ref [1]. The advantage of this method is that the measurement of the wire position, which may be the main error source, is no longer needed. This method has been adopted to measure the XiPAF PMQs. Figure 1: The PMQ to be used in XiPAF. Table 1: PMQ Tolerances Errors Name Values PMQ position δx, δy ± 0.17 mm PMQ pitch and yaw φx, φy ± 3 deg PMQ roll φz ± 0.6 deg PMQ integrated gradient ΔGl/Gl ± 1.5 % PMQ multipole contents Bn/B2 @R=8 mm n=3...15 1% MEASUREMENT SETUP As shown in Figure 2, a vibrating wire setup was constructed as described in [1]. A 1.2 m-long wire is stretched vertically by a plumb. The plumb is submerged into the water in order to rebalancing quickly after some disturbances. The 100 μm-diameter wire carries the sinusoidal current. The function generator is used to excite the wire to vibrate in the fundamental mode. The lower end of the wire is connected to the function generator, and the upper end is connected to the ground in the consideration of isolation. The fixed point of the plumb is separated from the lower end of the wire. The extra slack between the fixed point and the lower end is long enough in order to avoid disturbing the hanging plumb. The PMQ to be measured is on the top of the rotary table. The rotary table is installed on the mover in order to move in x and y directions. A vertical linear guide is beside the mover. It is used to check the perpendicularity of the PMQ. Two optocouplers, mounted in the perpendicular directions, are used as the wire vibration detectors to transduce the wire displacement into an electrical voltage. The signals from the sensor are sent to an oscilloscope. Two dial indicators are used to measure the magnet position change. _________________________________________ † email address zhengsx@tsinghua.edu.cn TUPMB009 Proceedings of IPAC2016, Busan, Korea ISBN 978-3-95450-147-2 1124 C op yr ig ht © 20 16 C C -B Y3. 0 an d by th e re sp ec tiv e au th or s 07 Accelerator Technology T09 Room-temperature Magnets Figure 2: The vibrating wire setup. EXPERIMENTS AND RESULTS Robustness in the Background Magnetic Field In Ref. [1], it has been illustrated that the results of the method mentioned will not be influenced by a stable background magnetic field. As shown in Figure 3, a 0.5 T dipole magnet is placed beside the set up. The magnetic center of one PMQ is measured with and without the dipole magnet beside. As shown in Figure 4, the difference between the results are smaller than 10 μm. Figure 3: Experiments on the influence of background magnetic field. -0.085 -0.080 -0.075 -0.070 90 °-2 70 ° Y 90 °-2 70 ° X 0° -18 0° Y 0° -18 0° X Without the magnet With the magnet

On the Feasibility of Sub-100 Nm Rad Emittance Measurement in Plasma Accelerators Using Permanent Magnetic Quadrupoles

A method of bunch by bunch measurement at nanoseconds interval by using cavity beam position monitors

Analysis of fringe field effects on measurement errors for Q-scanning-based emittance diagnosis system

A New Measurement Of Electron Beam Emittance With Cerenkov Radiation "Double Imaging" Method

Transverse Phase Space Diagnostics for Ionization Injection in Laser Plasma Acceleration Using Permanent Magnetic Quadrupoles

Emittance Measurement along Transport Beam Line for Laser Driven Protons

Noninterceptive Transverse Emittance Measurements Using Bpm for Chinese Ads R&D Project

Emittance Preservation in the Presence of Ion Motion for Low-to-high Energy Stages of a Plasma Based Accelerator

Low-emittance Electron Bunches from a Laser-Plasma Accelerator Measured Using Single-Shot X-Ray Spectroscopy.

Multislit-Based Emittance Measurement of Electron Beam from a Photocathode Radio-Frequency Gun

FOUR-DIMENSIONAL TRANSVERSE EMITTANCE MEASUREMENT UNIT FOR HIGH INTENSITY ION BEAMS*

State Key Laboratory of Intense Pulsed Radiation Simulation and Effect ( Northwest Institute of Nuclear Technology ) , Xi ’ an 710024 , China

Emittance Preservation Through Density Ramp Matching Sections in a Plasma Wakefield Accelerator

A Resonant Cavity for Single-Shot Emittance Measurement

Transverse beam envelope measurements and the limitations of the 3-screen emittance method for space-charge dominated beams

Emittance Preservation for the Electron Arm in a Single PWFA-LC Stage Using Quasi-Adiabatic Plasma Density Ramp Matching Sections

Experimental Demonstration of an Emittance-Preserving Beam Energy Dechirper Using a Hollow Channel Plasma

An Emittance Measurement Device for a Space-Charge Dominated Electron Beam

Ultralow-emittance Measurement of High-Quality Electron Beams from a Laser Wakefield Accelerator

Transverse Emittance Measurement for the Heavy Ion Medical Machine Cyclotron

Thermal Emittance from Ionization-Induced Trapping in Plasma Accelerators