Abstract:Heterojunction with intrinsic thin-layer (HIT) solar cells attract attention due to their high open circuit voltage and stable performance. However, short circuit current density is difficult to improve due to light losses of transparent conductive oxide and hydrogenated amorphous silicon passivation (a-Si:H) layer and low absorption coefficient of crystalline silicon (c-Si). Silicon germanium alloy (Si/Si1-xGex) quantum wells and quantum dots are capable of improving low light utilization by strong optical absorption in the infrared region. In this article, opto-MoS2of the HIT solar cells integrated with Si/Si1-xGex quantum wells (HIT-QW) as a surface absorber are investigated by numerical simulation with Technology Computer Aided Design (TCAD). The influences of germanium content on the MoS2of HIT solar cells with long carrier lifetimes of Si1-xGex layers (p*) and defect-free a-Si:H/c-Si interface are investigated at first. The simulation results indicate that optical utilization in the infrared region is enhanced with the increase of germanium fraction, while open circuit voltage degrades due to the decreasing of the energy band gap of Si1-xGex, radiative recombination and auger recombination mechanism in the Si/Si1-xGex quantum wells. And the conversion efficiency reaches a maximum value at a germanium fraction of 0.25 then drops distinctly. When the germanium fraction increases from 0 to 0.25, the short circuit current density increases from 34.3 mA/cm2 to 34.8 mA/cm2, while the open circuit voltage declines from 749 mV to 733 mV. Hence, the conversion efficiency increases from 21.5% to 21.7% due to the fact that the enhancement of short circuit current density compensates for the reduction of open circuit voltage. When the germanium content increases to more than 50%, a serious open circuit voltage loss of more than 130 mV associated with the energy band gap loss of Si1-xGex arises in the HIT-QW solar cells, which indicates that the dominating carrier transport mechanism changes from shockley diffusion to recombination in the Si/Si1-xGex quantum wells. Subsequently, the influences of interface defects at a-Si:H/c-Si interface and bulk recombination centers in the Si/Si1-xGex quantum wells are discussed. Both interface holes at a-Si:H/c-Si interface and bulk holes in Si1-xGex quantum wells can be recombined through the interface defects at a-Si:H/c-Si interface and bulk recombination centers in the Si/Si1-xGex quantum wells, respectively, which restricts the position of hole fermi level in the open circuit condition. When the germanium fraction increases, the influence of interface defects at a-Si:H/c-Si interface becomes weak on the degradation of open circuit voltage compared with the significant influence of the bulk trap centers. Moreover, p* of longer than 510-5 s is necessary for the retention of electrical performance of HIT-QW solar cells by the simulation. Based on this research, high-efficiency HIT solar cells can be achieved by incorporating high-quality Si/Si0.75Ge0.25 quantum wells, which also requires the impactful passivation of a-Si:H/c-Si interface.

Design guidelines for a highly efficient high-purity Germanium (HPGe)-based double-heterojunction solar cell

PHOTOELECTRIC STRUCTURE DESIGN OF HIGH EFFICIENCY AMORPHOUS SILICON GERMANIUM SOLAR CELL BASED ON LIGHT MANAGEMENT AND BAND GAP PROFILING

High Efficiency Amorphous Silicon Germanium Solar Cells

Design of a High Efficiency p-Si Based Heterojunction Solar Cell with ln2S3 Window and NiO BSF Layers

Numerical analysis and performance study of a double-heterojunction GaAs-based solar cell

High Efficient Solar Cell Based on Heterostructure Constructed by Graphene and GaAs Quantum Wells

Numerical modeling of CuSbSe2-based dual-heterojunction thin film solar cell with CGS back surface layer

Design Simulation and Optimization of Germanium-Based Solar Cells with Micro-Nano Cross-Cone Absorption Structure

Optimum design and preparation of<i>a</i>‐Si/<i>a</i>‐Si/<i>a</i>‐SiGe triple‐junction solar cells

Optimum Design And Preparation Of A-Si/A-Si/A-Sige Triple-Junction Solar-Cells

Design principles of crystalline silicon/CsGeI 3 perovskite tandem solar cells using a combination of density functional theory and SCAPS-1D frameworks

Numerical optimization of inorganic p-Sb2Se3/n-ZrS2 heterojunction solar cells: achieving high efficiency through SCAPS-1D simulation

Solar power conversion: CuI hole transport layer and Ba3NCl3 absorber enable advanced solar cell technology boosting efficiency over 30

Numerical Simulation of Silicon Heterojunction Solar Cells with Si/Si1-xGex Quantum Wells

CH3NH3PbI3/GeSe bilayer heterojunction solar cell with high performance

Boosting Efficiency in Dual-Absorber RbPbBr 3 Perovskite Solar Cell: The Role of Two-Dimensional GeS and SnS 2 as Electron Transport Layers

Dual-Absorber Solar Cell Design and Simulation Based on Sb2Se3 and CZTGSe for High-Efficiency Solar Cells

Performance Optimization of MA0.5FA0.5PbI3/CsPbI3 Based Hybrid Perovskite Solar Cell emphasizing on Double Absorber Layer

Design and numerical investigation of CsPbI3/CsSn0.5Ge0.5I3 double‐absorption‐layer heterojunction perovskite solar cells based on SCAPS‐1D

Replacing the Electron-Hole Transport Layer with Doping: Scaps Simulation of Lead-Free Germanium-Based Perovskite Solar Cells Based on Csgei3

Optimization of intrinsic layer thickness, dopant layer thickness and concentration for a-SiC/a-SiGe multilayer solar cell efficiency performance using Silvaco software