Sage Fulco,Michal K. Budzik,Kevin T. Turner
Abstract:Material architecture provides an opportunity to alter and control the fracture process zone shape and volume by redistributing the local stresses at a crack tip. Properly designed structures can enlarge the plastic zone and enhance the effective toughness. Here, we use a pillar array as a model structure to demonstrate how variations in geometry at a crack tip control the size and shape of the plastic zone and can be used to engineer the effective toughness. Elastic–plastic finite element simulations are used to show how the pillar width, spacing, and height can be varied to tailor the size and shape of the plastic zone. A set of analytical mechanics models that accurately estimate the shape, volume, and resulting toughness as a function of the base material properties and geometry are also presented. A case study extends the analysis to sets of non-regular pillar arrays to illustrate how architecture can be used to alter toughness along the crack path.
What problem does this paper attempt to address?
The problem that this paper attempts to solve is how to control the crack growth process zone (process zone) of materials through geometric structures in order to enhance the toughness of materials. Specifically, the research aims to explore how to use structural design to change the shape and size of the plastic zone near the crack tip, thereby improving the effective toughness of materials.
### Main problems
1. **Enhancing toughness**: Traditional methods reduce the yield strength by changing the material composition and microstructure, thereby increasing the plastic zone radius and improving toughness, but this will lead to a decrease in material strength. This paper proposes a new mechanism, that is, to regulate the shape and size of the plastic zone through geometric structure design, so as to improve toughness without sacrificing strength.
2. **Geometric control of the plastic zone**: The research uses a columnar array as a model structure to show how to control the size and shape of the plastic zone by changing the geometric parameters of the columnar array (such as column width, spacing, and height), and then realize the engineering design of effective toughness.
3. **Combination of theory and simulation**: Through the combination of elastic - plastic finite element simulation and analytical mechanical model, the influence of different geometric parameters on the plastic zone is quantified, and the effectiveness of these models is verified.
### Specific problems
- How to regulate the plastic zone during crack growth through geometric structure design?
- What are the effects of different geometric parameters (such as column width, spacing, and height) on the size and shape of the plastic zone?
- How to use the changes of these geometric parameters to optimize the toughness of materials?
### Research significance
This research provides theoretical basis and experimental verification for regulating material toughness through geometric structure design, and has important application prospects especially in emerging fields such as additive manufacturing. Through reasonable design of the microstructure of materials, the toughness of materials can be significantly improved without sacrificing strength, which is of great significance for the development of high - performance structural materials.
### Key formulas involved
1. **Plastic zone radius**:
\[
r_p=\left(\frac{K_{IC}}{\sigma_y}\right)^2\frac{\cos^2(\theta/2)}{5 - 3\cos(\theta)}
\]
where \(K_{IC}\) is the fracture toughness, \(\sigma_y\) is the yield strength, and \(\theta\) is the angle measured from the crack plane.
2. **Effective toughness**:
\[
J^*=\frac{\partial}{\partial A}\left(\int_{\Omega_p}u_p\,dV\right)+2\gamma
\]
where \(J^*\) is the effective toughness measurement value, \(\Omega_p\) is the plastic zone volume, \(u_p\) is the plastic energy density, and \(\gamma\) is the surface energy.
3. **Relative effective toughness**:
\[
\frac{J^*}{J_0}\approx\frac{\Omega_p}{\Omega_0}+\delta_e
\]
where \(J_0\) is the toughness of the homogeneous material, \(\Omega_0\) is the plastic zone volume of the homogeneous material, and \(\delta_e\) is the elastic energy offset term.
Through these formulas, researchers can quantitatively analyze and predict the influence of different geometric structures on the toughness of materials.