Abstract:In this study, the process of carbon dioxide (CO2) capture directly from ambient air in a conventional monoethanolamine (MEA) absorption process was simulated and optimized using a rate-based model in Aspen Plus. The process aimed to capture a specific amount (148.25 Nm3/h) of CO2 from the air, which was determined by a potential application aiming to produce synthetic methane from the output of a 2.7 MW electrolyser (593 Nm3/h H2). We investigated the technical performance of the process by conducting a sensitivity analysis around different parameters such as air humidity, capture rate defined as a ratio of moles of CO2 captured during the process to the total mole of CO2 in the feed stream, CO2 loading of lean and rich absorption liquids and reboiler temperature, and evaluated the energy consumption and overall cost in this system. In order to meet the design requirement for standard packed columns, the rich absorption liquid was circulated to the top of the absorber. A capture rate of 50% was selected in this process as a baseline. At higher capture rates, the required energy per ton of captured CO2 increases due to a higher steam stripping rate, required in the desorber, and at lower capture rates, the size of equipment, in particular, absorber and blowers increases due to the need for processing a significantly larger volume of air at the given CO2 production volume. At the base case scenario, a reboiler duty of 10.7 GJ/tCO2 and an electrical energy requirement of 1.4 MWh/tCO2 were obtained. The absorber diameter and height obtained were 10.4 and 4.4 m, respectively. The desorber is found to be relatively small at 0.54 m in diameter and 3.0 m in height. A wash water section installed at top of the absorber decreased the MEA loss to 0.28 kg/ton CO2. However, this increased capital cost by around 60% resulting in CO2 capture costs of $1,691 per ton CO2 for the MEA base scenario. Based on the techno-economic analysis, assuming a non-volatile absorbent rather than MEA thereby avoiding a wash water section, and using an absorption column built from cheaper materials, the estimated cost per ton of CO2 produced was reduced to $676/tCO2. The overall cost range was between $273 and $1,227 per ton of CO2 depending on different economic parameters such as electricity ($20–$200/MWh) and heat price ($2–$20/GJ), plant life (15–25 years) and capital expenditure (±30%). In order to reduce the cost further, the use of innovative cheap gas-liquid contactors that operate at lower liquid to gas ratios is crucial.

Evaluating CO 2 Capture Performance of Trisolvent MEA–BEA–AMP with Heterogeneous Catalysts in a Novel Bench-Scale Pilot Plant

Evaluating CO2 Capture Performance of Trisolvent MEA–BEA–AMP with Heterogeneous Catalysts in a Novel Bench-Scale Pilot Plant

Evaluating Energy-Efficient Solutions of CO2 Capture Within Tri-solvent MEA+BEA+AMP Within 0.1+2+2–0.5+2+2 Mol/l Combining Heterogeneous Acid–Base Catalysts

Catalytic CO2 Desorption Study of Tri-Solvent MEA-EAE-DEEA with Five Solid Acid Catalysts

Development and testing of a new post-combustion CO2 capture solvent in pilot and demonstration plant

Experimental Study of the Absorption and Regeneration Performance of Several Candidate Solvents for Post-Combustion CO2 Capture

MEA-based CO2 capture: a study focuses on MEA concentrations and process parameters

Techno-Economic Assessment for CO2 Capture From Air Using a Conventional Liquid-Based Absorption Process

Metal Oxyhydroxide Catalysts Promoted CO2 Absorption and Desorption in Amine-Based Carbon Capture: A Feasibility Study.

Modelling and Process Analysis of Post-Combustion Carbon Capture with the Blend of 2-Amino-2-methyl-1-propanol and Piperazine

New Approach with Universal Applicability of Evaluating the Heat Requirements in Solvent Regeneration Process for Post-Combustion CO2 Capture

Comparative Techno-Economic Analysis of CO2 Capture Processes Using Blended Amines

Kinetics, Thermodynamics, and Mechanism of a Novel Biphasic Solvent for CO2 Capture from Flue Gas

Integration Study of a Hybrid Solvent MEA-Methanol for Post Combustion Carbon Dioxide Capture in Packed Bed Absorption and Regeneration Columns

Post-Combustion CO2 Capture Demonstration Using Supported Amine Sorbents: Design and Evaluation of 200 Kwth Pilot

Integration of membrane contactors and catalytic solvent regeneration for efficient carbon dioxide capture

Systematic study of aqueous monoethanolamine‐based CO2 capture process: model development and process improvement

Experimental And Rate-Based Modeling Study Of Co2 Capture By Aqueous Monoethanolamine

Simulation of a CO_2 Capture System Using Amine Solutions for Selection of Absorbents

Pilot-Scale Experimental Study on the CO2 Capture Process with Existing of SO2: Degradation, Reaction Rate, and Mass Transfer

Attapulgite as a cost-effective catalyst for low-energy consumption amine-based CO2 capture