Abstract:The deposition of ternary nitrides with the incorporation of carbon atoms into its structure has demonstrated to be a promising approach in the pursuit of wear-resistant and self-lubricating coatings. Firstly, both TiAlN and TiAlCN monolayers were deposited using direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS) onto quenched and tempered AISI H11 tool steel to be used as references. Acetylene was used as a carbon precursor, producing DCMS and HiPIMS TiAlCN coatings with 9.0 and 21.7 at.% C, respectively.Subsequently, TiAlN/TiAlCN multilayers of various designs were also developed as follows: 5×[10/500], 5×[50/500] and 5×[100/500] nm. Residual stresses of the coating systems were determined by X-ray radiation utilising an ETA-diffractometer with a Cu-Kα radiation source applying the sin2ψ method. Additionally, residual stresses depth gradients of the substrate before and after the deposition of the coatings were determined in a LEDDI 8-circle diffractometer equipped with a W-X-ray tube and operated in the energy-dispersive mode of diffraction. Great reduction of the compressive residual stresses in the coatings was observed after the introduction of carbon into the TiAlN coating structure, shifting from −1047 ± 149 to −307 ± 211 MPa for the DCMS and from −7035 ± 1361 to +989 ± 187 MPa for the HiPIMS coatings. In the multilayer coatings, compressive residual stresses increase along with the increment of the TiAlN interlayer. Additionally, residual stresses of the substrate in the near-surface are dragged from low compressive stresses (−218 ± 61) to tensile stresses in the range of 1000 to 2000 MPa for all the DCMS/substrate systems, a behaviour only presented in HiPIMS by the TiAlN monolayer. Wear coefficients of all the evaluated HiPIMS systems are notoriously lower than their DCMS counterparts. Compared to TiAlN, TiAlCN HiPIMS presented a lower coefficient of friction but a higher wear coefficient, which in turn was not reduced by the introduction of the multilayer systems. Finally, Scratch test and Rockwell C adhesion tests have shown higher adhesion of DCMS coatings than HiPIMS coatings, and a detriment of the monolayers adhesion by the implementation of TiAlN/TiAlCN multilayer systems. The understanding of the residual stresses, both in the coating and in the substrate, and the way they affect the tribomechanical performance of the system coating/substrate continues to be of great importance, especially for coatings deposited by new technologies such as HiPIMS and self-lubricating coatings.

Chemical vapor deposited TiCN/TiC multilayer coatings: On the interplay between coating architecture and mechanical properties

Two-Layer Nanocomposite TiC-Based Coatings Produced by a Combination of Pulsed Cathodic Arc Evaporation and Vacuum Electro-Spark Alloying

Ti/TiN multilayer coatings: deposition technique, characterization and mechanical properties

Influence of multi-interfacial structure on mechanical and tribological properties of TiSiN/Ag multilayer coatings

Effect of Multilayered Structure on Properties of Ti/TiN Coating

Influence of Layer Number on Microstructure, Mechanical Properties and Wear Behavior of the TiN/Ti Multilayer Coatings Fabricated by High-Power Magnetron Sputtering Deposition

Microstructure, mechanical properties and cutting performance of super-hard Ti(B,C,N) coatings prepared by chemical vapor deposition method

Mechanical properties, thermal stability and oxidation resistance of TiN/CrN multilayer coatings

(AlCrNbSiTi)N/TiN multilayer films designed by a hybrid coating system combining high-power impulse magnetron sputtering and cathode arc deposition

The influence of multilayer structure on mechanical behavior of TiN/TiAlSiN multilayer coating

Comparative Study of Multilayer Hard Coatings Deposited on WC-Co Hardmetals

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Tribological and mechanical behaviors of TiN/CNx multilayer films deposited by magnetron sputtering

Residual stresses and tribomechanical behaviour of TiAlN and TiAlCN monolayer and multilayer coatings by DCMS and HiPIMS

Properties and Performance of TiAlSiN and AlCrN Monolayer and Multilayer Coatings for Turning Ti-6Al-4V

Analysis of Different Complex Multilayer PACVD Coatings on Nanostructured WC-Co Cemented Carbide

Structural, Mechanical, and Thermal Properties of the TiAlTaN/TiAlBN Multilayer

Tribomechanical behavior of TiCN/TiAlN/WC-C multilayer film on cutting tool inserts for machining

Investigation of the Properties of Ti-TiN-(Ti,Cr,Mo,Al)N Multilayered Composite Coating with Wear-Resistant Layer of Nanolayer Structure

Mechanical, oxidation, and cutting properties of AlCrN/AlTiSiN nano-multilayer coatings

Mechanical Properties and Fracture Toughness of Multilayer Hard Coatings Using Nanoindentation