Abstract:Nickel based superalloys are widely used in such applications as gas turbine blades due to their excellent mechanical properties at elevated temperatures. Oxidation is one of the life limiting factors at such temperatures since it accelerates failure mechanisms, e.g. fatigue and creep. In this project, oxidation behavior of Ni-3Al-4.8Ti-9.5Co-14Cr (wt.%) superalloy was investigated under various testing conditions. The alloy was investment-cast with preferential crystal growth direction [100]. Isothermal oxidation tests were carried out at 800°C for 150h. Cyclic oxidation tests were then conducted between 100-800°C for 150 one-hour cycles. An additional one-hour cycle was tested to replicate real-life working condition of the alloy, which consisted of heating the samples up to 800°C followed by slow cooling to 400°C. During the testing, samples were periodically taken from the furnace and weighted with an accuracy of 10 -4 g to calculate the weight gain and to analyze the microstructure of formed oxide. Scanning electron microscopy (SEM) combined with energy-dispersive spectroscopy (EDS) and X-ray diffraction were used to study the microstructure of oxidation products. The results reveal that the highest amount of weight gain is obtained in isothermal testing, while the lowest in cyclic. Diffusion of Ti and Ni to the free surface results in the early-stage formation of needle-shaped oxide phases followed by severe oxidation of Cr and Al. The layer of chromium oxide is continuous while aluminum oxide is blocky at the deepest position from the free surface. Cracks form at the interface of carbide particles and gamma phase near the free surface of cyclic oxidation samples due to concentration gradient of Ni and Al. Precipitate-free zone are observed near the free surface of all the samples at the end of the tests, but internal oxidation does not occur significantly in all the samples. It is found that temperature fluctuation increases oxide spallation, which causes crack formation. At the same time, in isothermal testing, dense, crack-free layer of oxide form on the surface of superalloy.

The long-term isothermal oxidation and cyclic oxidation performance of anodized Ti48Al2Nb2Cr alloy

Thermal Oxidation Behaviour of Ti6Al7Nb and Ti6Al4V Alloys

Oxidation and tribological properties of anodized Ti45Al8.5Nb alloy

Improving the High-Temperature Oxidation Resistance of TiAl Alloy by Anodizing in Methanol/NaF Solution

Cyclic and Isothermal Oxidation Behavior of a Directionally Solidified Ni-Al-Ti-Co-Cr Superalloy

Oxidation Behavior and Electrical Property of A Ni-Based Alloy in Sofc Anode Environment

Early oxidation behavior of Ti50Al and Ti45Al8Nb alloys

Unraveling the Origin of the Excellent High-Temperature Oxidation Resistance of an AlCrFeNiTi Complex Concentrated Alloy

Cyclic oxidation behaviour of as-deposited Ni-11·5Cr-4·5Co-0·5Al superalloy sheet when heated at 800°C

Insight into the Oxidation Behavior and Excellent Internal Oxidation and Nitridation Resistance of Fe71.5-x(Ni, Cr, Ti)28.5Alx Complex Concentrated Alloys by Advanced Characterization

High temperature oxidation behavior of a novel Ni-Cr-W-Al-Ti superalloy

High-temperature oxidation behaviors and mechanisms in newly designed L1 2 -strengthened high-entropy alloys

Time-Resolved In-Situ Xrd Study on Oxidation Evolution of Ti2alnb-Based Alloys

Anisothermal Oxidation of Micro-Crystalline Ni-20Cr-5Al Alloy Coating at 850-1280°C

High-Temperature Oxidation of NbTi-Bearing Refractory Medium- and High-Entropy Alloys

Microstructural evolution and high-temperature oxidation mechanisms of a titanium aluminide based alloy

Influence of Thermal Oxidation Duration on the Microstructure and Fretting Wear Behavior of Ti6Al4V Alloy

Effect of Al content on the oxidation behavior of NiCoCrAlYHf alloys at 1100°C

Study on the high-temperature oxidation of AlCrFeCoNi-based high-entropy alloys with trace Si additions

Long-term oxidation behavior for Ni-5Al coating in Air-H 2 O at 650 °C

Non-Isothermal Oxidation Behaviors and Mechanisms of Ti-Al Intermetallic Compounds.