Abstract:Purpose The additive manufacturing process, such as fused filament fabrication based on material extrusion, fabricates the samples layer-by-layer. The various parameters in the process significantly affect the dimensions, structure and mechanical properties of the fabricated parts. The purpose of this paper is to investigate the surface and mechanical properties that can affect the contact characteristics with other materials during tribological tests. Design/methodology/approach The investigation of 3D-printed Polyetheretherketone (PEEK) includes the measurement of dimensions, microhardness, surface roughness, surface energy and tensile strength to define material characteristics. The crystallinity is measured using an X-ray diffractometer to understand the hardness behaviour. Findings The printing parameters affect its surface roughness, hardness and crystallinity. This change in parameters such as layer thickness and infill density impacts mechanical properties such as hardness and surface roughness, which will influence the contact mechanism with the counter body during any tribological test. The change in a single parameter during the sample fabrication and the change in the surface and mechanical properties are observed. Research limitations/implications The material cost plays an important role in conducting numerous destructive tests, which is a major limitation to conducting parameter optimisation by varying more parameters. The study is limited to the as-fabricated samples rather than finished samples and without any heat treatment. Achieving optimal parameters is integral to the success of additive manufacturing, ensuring the production of components with consistent performance. Practical implications The study aims at the application of 3D-printed PEEK for bush or journal bearings that can be directly used in practice. The mechanical properties discussed in this paper can fill the gap between theory and practice. Social implications The research provides all fundamental properties, including the printing parameters and their effect on the dimensions and surface structure, which are required to understand the material and its use. The results are consistent as at least four samples were tested for tribological behaviour. The conclusion is updated as per suggestions. Originality/value The study outlines the relationship between the change in layer thickness and infill density with changes in surface energy, surface roughness, hardness and tensile strength. The deformation and adhesion during the friction test depend on these properties.

Tribological performance of 3D printed neat and carbon fiber reinforced PEEK composites

Tribological behavior of modified polyetheretherketone composites in sliding against stainless steel under water lubrication

Tribological Performance and Enhancing Mechanism of 3D Printed PEEK Coated with In Situ ZIF-8 Nanomaterial

3D-Printed high performance PEEK/CF-PEEK polymer composites—An investigation on microstructural characteristics and mechanical performance

Multifunctional performance of carbon nanotubes and graphene nanoplatelets reinforced PEEK composites enabled via FFF additive manufacturing

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

An investigation of the microstructure and tribological behavior of polyether ether ketone composites fabricated by extrusion‐based additive manufacturing

Mechanical, microstructural and numerical investigations of 3D printed carbon fiber reinforced PEEK

In-house processing of carbon fiber-reinforced polyetheretherketone (CFR-PEEK) 3D printable filaments and fused filament fabrication-3D printing of CFR-PEEK parts

Tribological and mechanical characterization of carbon-nanostructures based PEEK nanocomposites under extreme conditions for advanced bearings: A molecular dynamics study

Carbon Fiber Reinforced PEEK Composites Based on 3D-Printing Technology for Orthopedic and Dental Applications

Effect of composite processing technique on tribological properties of 3D printed PLA-graphene composites

Impact of processing defects on microstructure, surface quality, and tribological performance in 3D printed polymers

Tribological Performance Study of Low-Friction PEEK Composites under Different Lubrication Conditions

Material Extrusion 3D Printing of PEEK-Based Composites

Biotribological properties of 3D printed high-oriented short carbon fiber reinforced polymer composites for artificial joints

Mechanical and surface characterisation of additively manufactured polyetheretherketone for the tribo test

Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing

Tribological Behavior and Mechanical Properties of Graphene/PEEK Composites

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Mechanical performances of printed carbon fiber-reinforced PLA and PETG composites