Abstract:A concept of incorporating aligned multi-walled carbon nanotubes (MWCNTs) in the adhesive layer has been demonstrated to enhance the through-thickness thermal conductivity in the adhesively bonded joints. Both numerical and experimental studies were performed to determine key components in improving the through-thickness thermal conductivity and to realize the improvement in an adhesively-jointed system. The numerical analysis indicated that the key components to improve the through-thickness thermal conductivity in the adhesive joints are using highly conductive vertically aligned nanotubes as well as the thermal conductivity and the size of a transition zone between the nanotube ends and surrounding matrix materials in the form of either the adhesive or adherends. Therefore, the thermal contact of the conductive phase (the MWNT in this case) with the adherent surfaces is essential to achieve the desirable through-thickness thermal conductivity in joints. This theoretical observation was demonstrated experimentally by using conductive graphite facesheets as adherends and the polymer adhesive layer with the aligned MWCNTs. To ensure the ends of the MWCNTs make thermal contact with the adherent surfaces, the surface of the adhesive with the MWCNTs were plasma-etched and coated with thin Au layer, along with the surface of the graphite facesheet coated with thin Au–Pd layer. The measured value of the through-thickness thermal conductivity of the modified adhesive joint with the MWNCT was over 250W/mK, which superseded the thermal conductivity of neat adhesive joint by several order of magnitudes. Thus the study demonstrates a new approach as well as opportunities of much needed thermal property tailoring in structural joints.

Aminated carbon nanotube enhanced composite T‐joints mediating CFRP load‐bearing capacity improvement

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Strengthening of Composite T-joints Using Ø 0.11 Mm Z-pins Via an Ultrasound-Guided Insertion Process

Interfacial Strengthening and Self-Monitoring in Carbon Fiber-Reinforced Composites via Carbon Nanotube-Based Damage Sensors

Interfacial enhancement of CFRP/titanium alloy bonding joint by constructing a 3D interconnected CNTs network

Synergistic enhancement effect of flame-grown carbon nanotubes and chopped carbon fibers on adhesive joint of thermosetting laminate

Synergistic toughening on CFRP via in-depth stitched CNTs

The Carbon Nanotubes Effect into Single-lap Joint Failure Modes and Load Capacity: a Macromechanical Analysis

Effect of chemically grafted CNTs onto carbon fiber on the mechanical properties of fiber metal laminates

Interfacial Enhancement by CNTs Grafting towards High-Performance Mechanical Properties of Carbon Fiber-Reinforced Epoxy Composites

Effect of CNT film interleaves on the flexural properties and strength after impact of CFRP composites

A multi-layer resin film infusion process to control CNTs distribution and alignment for improving CFRP interlaminar fracture toughness

Reinforcing Adhesives Using Carbon Nanotubes for the Carbon Fibre Reinforced Plastic Composite and Metal Joint

A nanomodified-ultrasonic method to improve the shear strength of adhesively bonded composite joints

Growing carbon nanotubes in-situ via chemical vapor deposition and resin pre-coating treatment on anodized Ti-6Al-4V titanium substrates for stronger adhesive bonding with carbon fiber composites

Improving Tensile Properties of Double-Walled Carbon Nanotube Strands by Intercalation of Epoxy Resin

Reinforcing the Bandaged Joint of Double-Walled Carbon Nanotube Strands by Intercalation of Epoxy Resin

Enhancement of through-thickness thermal conductivity in adhesively bonded joints using aligned carbon nanotubes

Mechanical performance of a CFRP composite reinforced via gelatin-CNTs: A study on fiber interfacial enhancement and matrix enhancement

Interlaminar properties of carbon nanotubes modified carbon fibre fabric reinforced polyimide composites

Enhanced interlaminar structure and dynamic mechanical properties of Tectona grandis fiber (TGF)/polypropylene fiber (PPF)/carbon nanotube (CNT) nano composite prepared solid dipping coating process