Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

NASICON Electrodes: A Low‐Temperature Sodium‐Ion Full Battery: Superb Kinetics and Cycling Stability (Adv. Funct. Mater. 11/2021)

High-performance aqueous symmetric sodium-ion battery using NASICON-structured Na 2 VTi(PO 4 ) 3

A Low‐Temperature Sodium‐Ion Full Battery: Superb Kinetics and Cycling Stability

Enhanced low-temperature sodium storage kinetics in a NaTi2(PO4)3@C nanocomposite

Heterogeneous NASICON-Type Cathode With Reversible Multielectron Reaction for High-Performance Sodium-Ion Batteries

Modification of NASICON Electrolyte and Its Application in Real Na-Ion Cells

Reversible Multielectron Redox in NASICON Cathode with High Energy Density for Low-Temperature Sodium-Ion Batteries

A Strategy of High Entropy Enabling Advanced NASICON Sodium-ion Cathodes with High Stabilization and Multicationic Redox

Challenges and Perspectives for NASICON-Type Electrode Materials for Advanced Sodium-Ion Batteries

A NASICON-type Na3.67Cu0.17Fe0.5V1.33(PO4)3 cathode with multi-electron reaction for high-energy sodium-ion battery

Interface Ionic/Electronic Redistribution Driven by Conversion‐Alloy Reaction for High‐Performance Solid‐State Sodium Batteries

A Novel NASICON‐Typed Na 4 VMn 0.5 Fe 0.5 (PO 4 ) 3 Cathode for High‐Performance Na‐Ion Batteries

High performance NASICON ceramic electrolytes produced by tape-casting and low temperature hot-pressing: Towards sustainable all-solid-state sodium batteries operating at room temperature

Multifunctional-Element Doping of NASICON-Structured Cathode Enables High-Rate and Stable Sodium Storage

Achieving a Rapid Na+ Migration and Highly Reversible Phase Transition of NASICON for Sodium‐Ion Batteries with Suppressed Voltage Hysteresis and Ultralong Lifespan

New-type Hf-based NASICON electrolyte for solid-state Na-ion batteries with superior long-cycling stability and rate capability

Synthesizing Porous NaTi2(PO4)3 Nanoparticles Embedded in 3D Graphene Networks for High-Rate and Long Cycle-Life Sodium Electrodes.

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

Rechargeable Sodium Solid‐State Battery Enabled by In Situ Formed Na–K Interphase

Robust sodium storage enabled medium entropy Na3.5V0.5Mn0.5Fe0.5Ti0.5(PO4)3 NASICON with multielectron reaction for sodium-ion battery

Improved Electrochemical Performance of NASICON Type Na3V2- xCox(PO4)3/C (x = 0-0.15) Cathode for High Rate and Stable Sodium-Ion Batteries