Abstract:In order to improve the hardenability and toughness of high boron alloys, XCu (X = 0, 0.5, 1, 1.5, 2, 3, weight %) were added into high boron alloys. The Cu precipitation behavior and its effect on hardenability, microstructure, crystallography and mechanical properties of as-cast Fe-B-C-Cu alloys have been investigated systematically by means of SEM, XRD, TEM, EPMA and EBSD. The results indicate that Cu improves the hardenability of Fe-B-C-Cu alloys, while excessive Cu atoms segregating at the matrix attaching to boride promote the appearing of nano-Cu precipitation with body-centred cubic (bcc)structure, which can act as heterogeneous nuclei of the pearlite, leading to the reduction of hardenability. Therefore, the Cu concentration in Fe-B-C-Cu alloys should be controlled below 2wt%. Observation of TEM reveals that the orientation relationship(OR) between martensite and retained austenite are [001]α // [011]γ and [110] α//[1(−)1(−)1] γ. As well, the OR between ferrite and M3C are (100)M// (010)M3C and [011]M//[001]M3C. EBSD analysis shows that the misorientation angles of the α-Fe and M2B phases are mainly low-angle with less than 5°. The α-Fe phase has the preferred crystal plane (111) // ND-type grain, while the M2B phase displays a preferred growth orientation [002] on the M2B crystal plane (001). A possible OR between borides and α-Fe in Fe-B-C-Cu alloys is (001)α-Fe //(001)M2B. In addition, the bulk hardness and impact toughness increase obviously with 1–2wt% copper concentration owing to the increasing of volume fraction of martensite(Vm), which maybe a guiding copper addition in Fe-B-C-Cu alloys.

IMPROVEMENT OF MECHANICAL PROPERTIES AND CORROSION RESISTANCE OF Cu-Ni ALLOY BY TRACE OF BORON ADDITION

Influence of Ni Addition on Corrosion Performance of Medium-temperature Filler Metal with Low Cu Content for Al Brazed Joints

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Improved Corrosion Resistance of Ni‐Based Alloys by B‐Induced Passivation Behavior

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

The Enhancement of the Mechanical Properties and the Shape Memory Effect for the Cu-13.0Al-4.0Ni Alloy by Boron Addition

Effect of Copper on Properties of High Boron Iron-Base Alloy

Wear Resistance and High-Temperature Compression Strength of Fcc CuCoNiCrAl 0.5 Fe Alloy with Boron Addition

Effects of Mo and B Additives on Hardness and the Resistance of Cu–Ni Alloy to Wear, Corrosion and Corrosive Wear

Effects of Al addition on corrosion behavior and mechanical property of high-strength and high-elasticity Cu-20Ni-20Mn-0.3Nb-0.3Cr-0.3Zr alloy

Improvement of Interfacial Wetting and Mechanical Electrical Properties of Cu-B/ Sintered-Carbon Composites

Effect of Cerium and Boron on Microstructures and Properties of Cu-Ni-Si Alloy

Effect of Cu on Microstructure, Crystallography and Mechanical Properties in Fe-B-C-Cu Alloys

The Effect of Boron Addition on the corrosion behavior of Ni Cr Modental alloy prepared by powder metallurgy.

Effect of Heat Treatment on the Highly Corrosion-Resistant Cu70ni27.7fe2.3 Alloy

Effect of Boron on the Corrosion Properties of Al0.5CoCrCuFeNiBx High Entropy Alloys in 1N Sulfuric Acid

The Effect of Boron on the Corrosion Resistance of the High Entropy Alloys Al[sub 0.5]CoCrCuFeNiB[sub x]

Effect of Boron Addition on the Microstructure and Properties of Ti-22Nb-6Zr Shape Memory Alloys

Effects of Boron Addition on the Microstructure and Mechanical Properties of γ′-Strengthened Directionally Solidified CoNi-Base Superalloy

The Effect Of Boron On The Corrosion Resistance Of The High Entropy Alloys Al0.5cocrcufenibx