Abstract:The decrease of superplastic forming temperature and improvement of post-forming mechanical properties are important issues for titanium-based alloys. Ultrafine-grained and homogeneous microstructure are required to improve both processing and mechanical properties. This study focuses on the influence of 0.01–2 wt.% B (boron) on the microstructure and properties of Ti-4Al-3Mo-1V (wt.%) alloys. The microstructure evolution, superplasticity, and room temperature mechanical properties of boron-free and boron-modified alloys were investigated using light optical microscopy, scanning electron microscopy, electron backscatter diffraction, X-ray diffraction analysis, and uniaxial tensile tests. A trace addition of 0.01 to 0.1 wt.% B significantly refined prior β-grains and improved superplasticity. Alloys with minor B and B-free alloy exhibited similar superplastic elongations of 400–1000% in a temperature range of 700–875 °C and strain rate sensitivity coefficient m of 0.4–0.5. Along with this, a trace boron addition provided a stable flow and effectively reduced flow stress values, especially at low temperatures, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of superplastic deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1%. Post-forming heat treatment, including quenching and ageing, increased strength characteristics of the alloys with 0.01 and 0.1% boron by 90–140 MPa and insignificantly decreased ductility. Alloys with 1–2% B exhibited an opposite behavior. For the high-boron alloys, the refinement effect of the prior β-grains was not detected. A high fraction of borides of ~5–11% deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2% B demonstrated non-superplastic behavior and low level of strength properties; meanwhile, the alloy with 1% B exhibited superplasticity at 875 °C with elongation of ~500%, post-forming yield strength of 830 MPa, and ultimate tensile strength of 1020 MPa at room temperature. The differences between minor boron and high boron influence on the grain structure and properties were discussed and the mechanisms of the boron influence were suggested.

The Enhancement of the Mechanical Properties and the Shape Memory Effect for the Cu-13.0Al-4.0Ni Alloy by Boron Addition

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Effect of B on Shape Memory Properties and Microstructure of Fe14Mn6Si9Cr5Ni Alloy and Its Mechanism

Improved phase stability and mechanical properties in Ni-Mn-Sn-B Alloys: Experiments and first-principles calculations

Simultaneously improved strength and ductility of low-cost Ti-Al-V-Fe alloy with TiB 2 addition and thermomechanical processing

Strength–ductility balance optimization of Fe2NiCr0.5Cu0.2Al0.3Ti0.1 multicomponent alloy via doping trace amounts of boron

Wear Resistance and High-Temperature Compression Strength of Fcc CuCoNiCrAl 0.5 Fe Alloy with Boron Addition

Simultaneous enhancement of strength and ductility in quaternary Ti–V–Al–B light weight shape memory alloys with high transformation temperature

Effect of Boron on the Microstructure, Superplastic Behavior, and Mechanical Properties of Ti-4Al-3Mo-1V Alloy

Boron'S Effect on Martensitic Transformation and Magnetocaloric Effect in Ni43mn46sn11bx Alloys

Effects of Boron Addition on the Microstructure and Mechanical Properties of γ′-Strengthened Directionally Solidified CoNi-Base Superalloy

Enhancing mechanical properties of the boron doped Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy via tuning composition and microstructure

Effect of Varying Beryllium Addition on Microstructure, and Corrosion Behaviors of Cu-Zn-Al Shape Memory Alloys

Effect of Stoichiometry on Shape Memory Properties of Ti-Ni-Hf-Cu-Nb Shape Memory Alloys Manufactured by Suspended Droplet Alloying

Effect of Copper on Properties of High Boron Iron-Base Alloy

Effect of Cu content on martensitic transformation and shape memory behavior in Ti31.5Hf15Zr5Ni48.5−xCux alloys

Effect of Al content on thermal stability, shape memory effect and mechanical properties of Cu–Al–Fe shape memory alloys

Boron microalloying for high-temperature eutectic high-entropy alloys

Effect of Boron on Hot Ductility and Room-Temperature Tensile Properties of Microalloyed Steels with Titanium and Niobium

Optimization of Performances in Ternary Ti-Nb-Cu Shape Memory Alloys on the Basis of D Electron Theory

Effect of Boron Microalloying on Microstructure and Thermoelastic Martensitic Transformation in Aged NiFeGa(B) Alloys