Abstract:The microstructure evolution and mechanical properties of Al–3.92Cu–1.10Li–0.68Mg–0.32Ag–0.23Mn–0.35Zn–0.11Zr and Al–3.92Cu–1.12Li–0.76Mg–0.29Ag–0.24Mn–0.24Zn–0.12Zr–0.083Sc (wt%) alloys during homogenization with different cooling modes were comprehensively studied. It was clearly revealed that the minor Sc addition refined the grains of as-cast Al–Cu–Li–Mg alloys through the formation of primary Al3(Sc, Zr) phases during the solidification process, and induced Sc enrichment in the θ (Al2Cu) eutectic. After the homogenization treatment, the majority of coarse nonequilibrium eutectic phases at the grain boundaries dissolved into the α-Al matrix, leading to the relatively uniform distribution of each element. Sc-added alloy after homogenization treatments possessed more superior strength and ductility than Sc-free alloy. Compared to the furnace cooling mode, the air cooling mode could inhibit the precipitation of micron-sized coarse T1 (Al2CuLi) phase and improve the mechanical properties of the alloys. After homogenization, the continuous Al2Cu phase in the as-cast Sc-added alloy dissolved and transformed to an array of W-(Al, Cu, Sc) ternary phase, which was identified as Al6Cu6Sc with the body-centered tetragonal structure. The appearance of spherical Al6Cu6Sc particle could not damage the mechanical properties of Al–Cu–Li–Mg alloys after the homogenization treatment. The tensile strength, yield strength and elongation of Sc-added alloy after the homogenization by air cooling were 390 MPa, 265 MPa and 10.8%, respectively. The investigation of Al6Cu6Sc phase offered a potential avenue to produce high-quality Sc-added 2xxx series alloys.Graphic

3D local atomic structure evolution in a solidifying Al-0.4Sc dilute alloy melt revealed in operando by synchrotron X-ray total scattering and modelling

Effects of Sc on the Vacancy and Solute Behaviours in Aluminium

Morphology evolution and growth mechanism of primary Al3Sc and eutectic Al3Sc in Al-Sc alloys

Evolution of local atomic structure during solidification of Al 2Au liquid: An ab initio study

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Computational engineering of sublattice ordering in a hexagonal AlHfScTiZr high entropy alloy

Connecting short-range order for the liquid-solid transition of Al-Cu-Fe alloys

Cast Microstructure and Crystallographic Features of Al3Sc Dendrites in High Sc-Contained Al-Sc Alloys

Microstructure evolution and microhardness of the novel Al–Cu–Li-xSc alloys fabricated by laser rapid melting

Experimental Andab Initiomolecular Dynamics Simulation Studies of Liquidal60cu40alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Evolution of Atomic Structure in Al75cu25 Liquid from Experimental and Ab Initio Molecular Dynamics Simulation Studies

On the Sc induced solidification-heterogeneous microstructure in selective laser melted Al-5Mn alloys

Effect of minor Sc additions on precipitation and mechanical properties of a new Al-Cu-Li alloy under T8 temper

Ab initio study of local structures during cooling of liquid Fe-C and Fe-Cr-C alloys

Effect of Sc content on microstructure characteristics and evolution of W phase in Al–Cu–Li alloys under as-cast and homogenization conditions

Structural correlation and chemistry of molten NaF–ScF3 with dissolved metal aluminium: TG/DTA, XRD, NMR and molecular dynamics simulations

Ab initio Molecular Dynamics Study of Local Atomic Structure Evolution of U–Zr Alloy Melts upon Solidification

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

Investigation of W phase crystal structure and evolution mechanism based on Al-Cu-Sc alloy during homogenization

Formation and Relative Stabilities of Core-Shelled L12-Phase Nano-structures in Dilute Al–Sc–Er Alloys