Abstract:This study investigates the relationship between aging temperature on the precipitation behavior and mechanical properties of a gravity cast Al-5.0Mg-3.0Zn-1.0Cu (wt%) alloy. After solution treatment at 470 °C for 24 h, alloys were aged at 120, 150 and 175 °C. Upon analyzing the samples, the alloys displayed different age hardening behaviors due to the variations in aging temperature. An increase in aging temperature not only reduced the peak aging time significantly, but also changed the distribution of precipitates. Numerous GPII zones and T′ precipitates (precursors of T-Mg32(AlZn)49) were homogeneously distributed within matrix at a higher aging temperature and the volume fraction of T′ precipitates increased. Tensile test results for peak-aged samples determined that both yield strength (YS) and ultimate tensile strength (UTS) increased, while elongation (EL) decreased with increasing temperature. The increase in the YS can be attributed to the higher volume fraction of T′ precipitates caused by the higher aging temperature. Moreover, the impact toughness decreased (due to a continuous decrease in EL) as the aging temperature increased. By adjusting aging temperature from 120 to 175 °C, YS increased from 377 to 451 MPa, while EL decreased from 13.8% to 5.2%. After peak aging treatment at 150 °C, the alloy appears to possess optimal mechanical properties with YS, UTS, EL and toughness being 441 MPa, 496 MPa, 9.6%, and 8.1 J/cm2, respectively. These finding suggest that there are many potential advantageous applications for this alloy within automobile components requiring high strength and toughness.

Effect of multi-stage aging on the precipitation strengthening and mechanical properties for an Al-Mg-Si-Ag alloy

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

Effects of Aging Temperature on the Mechanical Properties and Precipitation Behavior of a Pre-strained Al–Cu–Mg–Ag Alloy

Effect of In addition on the precipitation behavior and mechanical property for Al-Mg-Si alloys

Effect of Artificial Aging Treatment on the Mechanical Properties and Regulation of Precipitated Phase Particles of High-Pressure Die-Cast Thin-Wall AlSi10MnMg Longitudinal Carrier

Effect of aging route on the precipitation behavior and thermal stability of Al-Cu-Mg-Ag alloy

Precipitation behavior of an Al–Cu–Li–X alloy and competing relationships among precipitates at different aging temperatures

Regulation of precipitation behavior among T1, S', and θ' phases in Al–Cu–Li-(Mg–Ag) alloys by optimizing Ag/Mg ratios

Precipitation Behavior and Strengthening Mechanism of Extruded 2196 Al-Cu-Li Alloy Plate during Multi-Step Age-Hardening Treatment

Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys under Multi-Directional Severe Strain and Aging

Precipitates evolution and strengthening of Al–Mg2Si alloys containing high-Cu contents during ageing process

Effect of combined addition of Ag and Cu on the precipitation behavior for an Al-Mg-Si alloy

Effects of aging treatment on the precipitation behaviors and mechanical properties of Al-5.0Mg-3.0Zn-1.0Cu cast alloys

Effects of Mg/Zn ratio and pre-aging on microstructure and mechanical properties of Al–Mg–Zn–Cu alloys

Quantitative evaluation of the effect of Ag-addition on the concurrently-existing precipitation kinetics in the aged Al-Cu-Mg(-Ag) alloys

Influence of Mg Contents on Aging Precipitation Behavior of Al–3.5Cu–xMg Alloy

Clustering and Precipitation during Early-Stage Artificial Aging of Al–Si–Mg(–Cu) Foundry Alloys

Early-Stage Precipitation Phenomena and Composition-Dependent Hardening in Al-Mg-Si-(Cu) Alloys

Effect of the Solid Solution and Aging Treatment on the Mechanical Properties and Microstructure of a Novel Al-Mg-Si Alloy

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Effect of silicon content on nucleation and growth of multiscale precipitates in Al–Mg–Si–Cu–Zn alloys for different aging paths