Abstract:Modern microelectronic components for high-power and high-frequency applications based on III-V compound semiconductors offer high break down voltage (GaN: 5 MV/cm and AlN: 15 MV/cm) at low specific on-resistance. However, it requires reliability and reproducibility of the production processes. Going to higher frequencies (5 GHz and beyond) and more integration in consumer electronics, smaller structure sizes are needed. This is going along with increasing demands on the manufacturing processes like dry etching. The main goal is to reach smaller and high controllable etching rates, going down to single atomic layers, low damage, and minimized surface roughness. Atomic layer etching (ALE) represents a key technology in order to achieve such requirements. An ALE process consists of two independent steps forming a repeatable cycle with a specific etching amount per cycle (EPC). First a surface modification is done by a chemical precursor i.e., adsorbing or oxidizing the surface. The second step is the removal of the modified layer, either physically by low energy non-reactive ion bombardment (Plasma Enhanced ALE [PEALE]) or chemically by a reactive species (Thermal ALE). The two steps are separated by an inert gas purge. This purging grants the removal of the chemistry after the first step, preventing further chemical reaction and transporting the chemical products out of the chamber after the second step. In this study, a PEALE conducted on different tools is used, for gate and contact recess study in a AlGaN/GaN heterostructure to form high electron mobility transistors (HEMT) with reduced ohmic contact resistance and threshold voltages. The results show a reduction of ohmic contact resistance at reduced forming temperatures and a linear dependence of the threshold voltage on gate recess depth. In order to determine the etching rate and roughness, atomic force microscopy (AFM) measurements were performed. The PEALE module is either integrated into a cluster tool consisting of atomic layer deposition (ALD) and chemical vapor deposition (CVD) or done in a combined ALD/ALE chamber. This opens the possibility of etching and depositing in-situ , reducing contamination and degradation of the substrate material. By this means, metal insulator semiconductor (MIS)-HEMTS with a recessed gate are studied. The monitoring of the individual processes is achieved by test structures like transfer length method structures (TLM) and metal oxide semiconductor (MOS), which showed the improved electric performance of these devices and may indicate unwanted interface issues, respectively. Additional, pre- and post-treatments could improve the interfaces further. The results will be presented and discussed in terms of ALE process development and optimization. This work was financially supported within the ALEStar project by the government of the Free-state of Saxony and the European Regional Development Fund under grant no. SAB 100402929.

Oxygen-based digital etching of AlGaN/GaN structures with AlN as etch-stop layers

Atomic layer etching technique for InAlN/GaN heterostructure with AlN etch-stop layer

Spacer Side-wall Processed 0.15 Μm GaN HEMT for Ka-band Application

Pulsed N2 Plasma Surface Treatment for AlGaN/GaN HEMTs Prior to PECVD SiNx Passivation to Reduce Plasma Damage

Highly Selective Dry Etching of GaN over AlGaN Using Inductively Coupled Cl2/N2/O2 Plasmas

Highly Selective Dry Etching of Gan over Algan Using Inductively Coupled Cl-2/N-2/O-2 Plasmas

Oxidation-based Wet-Etching Method for Al Ga N/Ga N Structure with Different Oxidation Times and Temperatures

High-Performance Normally-Off ${\rm Al}_{2}{\rm O}_{3}/{\rm GaN}$ MOSFET Using a Wet Etching-Based Gate Recess Technique

A Novel Oxidation-Based Wet Etching Method For Algan/Gan Heterostructures

The reactive ion etching characteristics of AlGaN/GaN SLs and etch-induced damage study of n-GaN using Cl2/SiCl4/Ar plasma

Morphological and Electrical Characterization of AlGaN/GaN Heterostructures Modified By Atomic Layer Etching

Etch-stop process for precisely controlling the vertical cavity length of GaN-based devices

A GaN HEMT Structure Allowing Self-Terminated, Plasma-Free Etching for High-Uniformity, High-Mobility Enhancement-Mode Devices

Control of Surface Chemistry in Recess Etching Towards Normally‐OFF GaN MIS‐HEMTs

Ultralow-Supersaturation Al Pretreatment Toward Low Dislocation Density and Low Radio Frequency Loss GaN/AlN Epi-Stacks on High-Resistivity Si Substrates

Nonselective and smooth etching of GaN/AlGaN heterostructures by inductively coupled plasmas

NH3/N2 plasma treatment on etched AlGaN surface for high-performance p-GaN HEMTs fabrication

Nitride Spacer Aided 0.15 Μm AlGaN/GaN HEMT Fabrication with Optimized Gate Patterning Process

Dry Etching Characteristics of Algan/Gan Heterostructures Using Inductively Coupled H-2/Cl-2, Ar/Cl-2 and Bcl3/Cl-2 Plasmas

Nonselective etching of GaN/AlGaN heterostructures by Cl 2 /Ar/BCl 3 inductively coupled plasmas