Abstract:In this work, investigations of the magnetic microstructure of anisotropic sintered SmCo5 permanent magnets with high coercivity have been made using the colloid-scanning electron microscopy (SEM) technique and magnetic force microscopy (MFM). The magnets were produced by powder metallurgy (sintering) process and consisted of oriented grains with an average size of about 20μm. They were studied in the thermally demagnetized state. Owing to the application of digital image recording, enhancement and analysis, high-quality images of the magnetic microstructure were obtained and analyzed not only qualitatively but also quantitatively. Improvements over previous results were achieved. The grains show the presence of magnetic domains, as expected. At the surface perpendicular to the alignment axis, the coarse domain structure in the form of a maze pattern with surface reverse spikes is observed. The main (maze) domains had typical widths 3–5μm. The reverse spike domains were imaged as circles typically 1–2μm in diameter or as elongated regions up to about 6μm in length. Interestingly, in addition to the coarse maze domains and reverse spikes near the surface, a fine surface domain structure is revealed with MFM. The fine scale domains are found to be magnetized perpendicular to the surface and their occurrence is attributed to further reduction of the magnetostatic energy at the cost of a larger domain wall energy. On the surface parallel to the alignment axis, the main domains within individual grains are imaged as stripe domains with domain walls running approximately parallel to the alignment axis, while reverse spike domains are displayed in the form of triangular domains and occur near some grain boundaries, pores or precipitations. The magnetic alignment of grains was found to be good, but certainly not perfect. In most cases the domain structures within grains were independent of their neighbors, but in some cases (not so rare) observations indicated the existence of significant magnetostatic coupling between neighboring grains. The main and surface domain widths were determined by digital means using the stereologic method of Bodenberger and Hubert. Moreover, the domain wall energy and other intrinsic parameters for the studied magnets were determined.

Unconventional magnetization textures and domain-wall pinning in Sm-Co magnets

Temperature dependence of magnetization processes in Sm(Co,Fe,Cu,Zr)$_z$ magnets with different nanoscale microstructures

Coercivity mechanism of high-performance anisotropic heterostructure SmCo 5 magnets

Pushing the limits of magnetic anisotropy in the Sm-Co system

Microstructural Characterization of Sm-Co Magnets

Coercivity and Transmission Electron Microscopy Study of Nanocomposite Sm–Co Powders by Mechanical Alloying

Study of magnetization reversal and magnetic hardening in SmCo 5 single crystal magnets

Studies of the domain structure of anisotropic sintered SmCo5 permanent magnets

Quantitative analysis of pinning-hardened intrinsic coercivity of Sm(CoFeCuZr)z (z = 7.0–7.8) high-temperature permanent magnets

Influence of amorphous phase on coercivity in SmCo5-Cu nanocomposites

Magnetoelectric Tuning of Pinning‐Type Permanent Magnets through Atomic‐Scale Engineering of Grain Boundaries

Microstructure and magnetic properties of SmCo5 sintered magnets

Microstructure, phase compositions, and coercivity evolution in micron-thick SmCo-based permanent magnetic films

Atomic‐Scale Transition Zones Determined Coercivity in Samarium‐Cobalt Based Permanent Magnets

Towards engineering the perfect defect in high-performing permanent magnets

Microwave-assisted chemical synthesis of SmCo 5 magnetic particles with high coercivity

First principles study of transition-metal substitutions in Sm–Co permanent magnets

Exploring microstructural origin of squareness-coercivity trade-off in iron-rich Sm-Co-Fe-Cu-Zr magnets

Strain Induced Anisotropic Magnetic Behaviour and Exchange Coupling Effect in Fe-SmCo$_{5}$ Permanent Magnets Generated by High Pressure Torsion

Formation of cellular/lamellar nanostructure in Sm$_2$Co$_{17}$-type binary and ternary Sm-Co-Zr magnets

Overcoming mechanical fragility in Sm-Co permanent magnet materials