Abstract:We have demonstrated an anisotropic bulk SmFe12-based sintered magnet with sufficiently large coercivity of μ0Hc=1.0 T and a remanence ratio (Mr/Ms) of 0.84 using conventional liquid sintering process of nitrogen jet-milled powders with the nominal composition of Sm8Fe73.5Ti8V8Ga0.5Al2 (at.%). The moderate saturation magnetization of μ0Ms =0.74 T is due to the dissolution of a large amount of stabilizing elements, Ti, V, and Al, in the 1:12 phase. The anisotropy field of the main 1:12 phase was determined to be µ0HA=10.2 T. Detailed multi-scale microstructure characterizations by scanning electron microscope (SEM) and scanning transmission electron microscope (STEM) showed the magnet consists of Sm(Fe,Ti,V,Al)12 grains with the ThMn12-type crystal structure with a size distribution of ∼3−15µm that are enveloped by ∼3 nm thick Sm-rich amorphous intergranular phase. Secondary phases including metallic (Sm,Ga)-rich, SmOx, and Fe2(Ti,V) phases coexist with the 1:12 phase. Measured angular dependence of coercivity follows Kondorsky type magnetization reversal, suggesting the coercivity arises due to the pining of magnetic domain walls. Magneto-optical Kerr effect (MOKE) microscopy revealed magnetization reversal starts at the grain boundaries and interphase interfaces and thin amorphous intergranular phases act as the pinning sites against magnetic domain wall propagation. Small micromagnetic parameter α∼0.164 estimated by fitting to the Kronmüllar equation suggest that the reduction of the grain size and engineering of the intergranular phase to an Fe-lean composition are necessary to improve the coercivity toward µ0HA/3=3.4 T. This work provides guidelines on an optimum microstructure to develop an anisotropic bulk SmFe12-based sintered magnet with a sufficiently large coercivity.

Strain Induced Anisotropic Magnetic Behaviour and Exchange Coupling Effect in Fe-SmCo$_{5}$ Permanent Magnets Generated by High Pressure Torsion

Influence of Severe Plastic Deformation on the Magnetic Properties of Sm‐Co Permanent Magnets

Manufacturing of Textured Bulk Fe-SmCo$_{5}$ Magnets by Severe Plastic Deformation

Influence of amorphous phase on coercivity in SmCo5-Cu nanocomposites

Structure and magnetic properties of nanocrystalline SmCo5 and SmCo3Cu2 prepared by using high-pressure torsion method

Ferromagnetic Composite with Stress-Insensitive Magnetic Permeability: Compensation of Stress-Induced Anisotropies

Magnetic Characterization of HPT-deformed Fe-Si Soft Magnetic Alloys Before and After Heat Treatment and Internal Stress Calculations

Magnetic Materials via High-Pressure Torsion of Powders

Coercivity mechanism of high-performance anisotropic heterostructure SmCo 5 magnets

Tuneable Magneto-Resistance by Severe Plastic Deformation

Origin of coercivity in an anisotropic Sm(Fe,Ti,V)12-based sintered magnet

On the magnetic nanostructure of a Co-Cu alloy processed by high-pressure torsion

Microstructure and extrinsic magnetic properties of anisotropic Sm(Fe,Ti,V)12-based sintered magnets

Pushing the limits of magnetic anisotropy in the Sm-Co system

Microstructural Characterization of Sm-Co Magnets

Unconventional magnetization textures and domain-wall pinning in Sm-Co magnets

Magnetostrictive Behavior of Severe Plastically Deformed Nanocrystalline Fe-Cu Materials

Phase separation and chemistry evolution in Fe-rich Sm(CobalFe0.31Cu0.07Zr0.025)7.7 magnets: The effect of initial defect

Magnetic Property Tunability of Amorphous SmCo Thin Films by Mechanical Strain Supplied by Flexible Substrates

Microstructural Changes Influencing the Magnetoresistive Behavior of Bulk Nanocrystalline Materials

Quantitative analysis of pinning-hardened intrinsic coercivity of Sm(CoFeCuZr)z (z = 7.0–7.8) high-temperature permanent magnets