Abstract:The effect of major constituents (the Li content increases from 0.5 to 3 wt% and the Cu content decreases from 4.5 to 2 wt%) on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations. Increasing the Li content progressively raises the melting temperature from 520 °C in 1# alloy (Al-0.5Li-4.5Cu, wt%) and 2# alloy (Al-1Li-4.5Cu) to 560 °C in 6# alloy (Al-3Li-2Cu). In addition, the variations of the major constituents result in the changes of the type and volume fraction of the inter- and intra-granular intermetallic phases. TEM results indicate that minor modifications to alloy composition greatly alter precipitation behavior during isothermal aging. The Li-poor alloy (2# alloy) presents a much shorter incubation time of T1-Al2CuLi precipitate than the Li-rich alloy (Al-1.5Li-4.5Cu, 3# alloy), while the nucleation of θ'-Al2Cu precipitate is promoted in Li-rich alloy. No typical spherical δ'-Al3Li precipitate is observed in 2# and 3# alloys during isothermal aging, except for the as-quenched 3# alloy. The preferential nucleation of δ' precipitate on the coherent and broad face of θ' precipitate is observed in 2# and 3# alloys, leading to the formation of "sandwich-like" δ'/θ'/δ' phases. Further decreasing Cu content to 2 wt% and increasing Li content to 3 wt% (6# alloy), the predominant phase in the matrix is δ' precipitate, accompanied by a small amount of unevenly distributed θ' and T1 precipitates. The best balance between ductility and strength is obtained by 2# alloy aged for 32 h, but 6# alloy has significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over 2# alloy (density: 2.675 g/cm3; elastic modulus: 75.45 GPa).

Microstructure and chemistry of the composite precipitate structure in Al-Li-Cu alloy

Investigation on formation mechanism of T1 precipitate in an Al-Cu-Li alloy

Interfacial structure evolution of the growing composite precipitates in Al-Cu-Li alloys

Atomic Structure of T1 Precipitates in Al–Li–Cu Alloys Revisited with HAADF-STEM Imaging and Small-Angle X-ray Scattering

Uncovering the influence of Cu on the thickening and strength of the δ′/θ′/δ′ nano-composite precipitate in Al–Cu–Li alloys

Combined electron beam imaging and ab initio modeling of T1 precipitates in Al–Li–Cu alloys

Microstructure evolution and shearing behaviour of δꞌ/θꞌ/δꞌ precipitates in an aged Al-Cu-Li-Mg aluminium alloy

First-principle investigation on the interfacial structure evolution of the δ'/θ'/δ' composite precipitates in Al-Cu-Li alloys

Fine precipitation scenarios of AlZnMg(Cu) alloys revealed by advanced atomic-resolution electron microscopy study Part I: Structure determination of the precipitates in AlZnMg(Cu) alloys

Heterogeneous nucleation of T1 precipitates in solid solution of Al-Cu-Li alloys from Ag-rich structures: An ab initio study

Study of the precipitate evolution mechanism in an Al-Mg-Si-Cu alloy with Si-rich and low Cu composition

Composite precipitates in a commercial Al–Li–Cu–Mg–Zr alloy

The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy

Effect of combined addition of Ag and Cu on the precipitation behavior for an Al-Mg-Si alloy

Characterization of precipitation in Al-Li alloy AA2195 by means of atom probe tomography and transmission electron microscopy

Co-precipitated Ni/Mn Shell Coated Nano Cu-rich Core Structure: A Phase-Field Study

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Interfacial Segregation and Precipitates Behavior in the Ultrafine Grained Al-based Metal Matrix Composites

Effects of cooling rates on precipitates in homogenized Al–Cu–Li alloy

First-principles study of crystal structure and stability of T1 precipitates in Al-Li-Cu alloys