Abstract:Statement of problem Three-dimensional (3D) printing of cobalt chromium (Co-Cr) removable partial dentures (RPDs)by selective laser melting (SLM) has been claimed to be less challenging than by conventional casting and provides significant improvements. However, the adaptation and fit of the SLM framework and the optimum build orientation are still unclear. Purpose The purpose of this in vitro and clinical study was to evaluate the effect of different build orientations on the adaptation of removable partial denture frameworks fabricated by SLM technology in vitro and to compare the adaptation of the SLM and conventional RPD frameworks clinically. Material and methods A master model simulating a maxillary arch of Kennedy class III modification 1 was scanned and duplicated to create a virtual 3D cast and reference cast. Four groups (n=40) of Co-Cr RPD frameworks were fabricated. For the SLM groups, the Co-Cr framework was virtually designed and exported for SLM printing. The SLM printing was done in 3 different build orientations: 0-degree (n=10), 45-degree (n=10), and 90-degree (n=10) groups. Other Co-Cr frameworks were conventionally cast (n=10). All Co-Cr frameworks were scanned and virtually superimposed with the master model using a surface-matching software program. The gap under 9 selected points in the palatal major connectors was analyzed and calculated. A smaller gap indicates more surface adaptation and close contact between the palatal major connector and the master model. The data were analyzed using the Kruskal-Wallis and Dunnett T3 tests (α=.05). Three patients with a partially dentate maxillary arch were enrolled in the clinical part based on inclusion criteria. Two RPD frameworks were provided for each patient (conventional casting and SLM printing). The adaptation of each framework was assessed by measuring the gap between the palatal major connector of the framework and the palate with light-body silicone. The differences in adaptation between the conventional and SLM frameworks were compared by using independent t tests (α=.05). Results The in vitro study identified significant differences in the adaptation of the palatal major connector among the 4 groups ( P <.001), except for conventional and 0-degree SLM printing ( P =.999). The conventional and 0-degree SLM frameworks exhibited the best adaptation, with the lowest gap underneath the palatal major connector of the RPD framework (0.01 ±0.02 mm and 0.01 ±0.01 mm, respectively). In the clinical part of the study, no significant difference was found between the adaptation of SLM and the conventional framework ( P =.430) Conclusions The adaptation of SLM printing can be maximized with less gap under the palatal major connector of the RPD framework when using the 0-degree build orientation. Co-Cr frameworks produced with SLM printing technology were comparable with conventionally produced frameworks; hence, SLM printed frameworks can be an alternative for clinical applications when optimum SLM parameters are applied.

Effect of different digital technology on the adaptation and retention of Co-Cr partial denture frameworks.

Adaptation of cobalt chromium frameworks fabricated by conventional versus selective laser melting techniques: An in vitro and clinical assessment

CLINICAL AND CYTOLOGICAL EVALUATION OF REMOVABLE PARTIAL DENTURE FABRICATED BY SELECTIVE LASER SINTERING ADDITIVE PROTOTYPING TECHNIQUE

Fit and Retention of Cobalt-Chromium Removable Partial Denture Frameworks Fabricated with Selective Laser Melting

Effect of finishing and polishing techniques on the fit accuracy and dimensions of conventional and CAD‐CAM removable partial denture frameworks

Mechanical properties of cobalt-chromium 3-unit fixed dental prostheses fabricated by casting, milling, and additive manufacturing

Preliminary Clinical Application of Removable Partial Denture Frameworks Fabricated Using Computer-Aided Design and Rapid Prototyping Techniques.

Comparison between selective laser melted and cast removable partial denture frameworks

Adaptation of Removable Partial Denture Frameworks Fabricated by Selective Laser Melting.

Effect of lamination layer thickness and abutment preparation on the fit of Co-Cr multi-unit prostheses fabricated by additive manufacturing: An in vitro study

Evaluation of trueness and precision of removable partial denture metal frameworks manufactured with digital technology and different materials

Effect of ceramic layering on the fit of cobalt-chromium alloy 3-unit fixed dental prostheses fabricated by additive, soft milling, and casting technologies

Evaluation of two printing techniques for maxillary removable partial denture frameworks

Fit of removable partial denture frameworks fabricated from 3D printed patterns versus the conventional method: An in vitro comparison

Influence of CAD/CAM Milling and 3D-Printing Fabrication Methods on the Mechanical Properties of 3-Unit Interim Fixed Dental Prosthesis after Thermo-Mechanical Aging Process

Accuracy of Mandibular Removable Partial Denture Frameworks Fabricated by 3D Printing and Conventional Techniques

CLINICAL EVALUATION OF POLYOXYMETHYLENE PARTIAL DENTURES DESIGNED AND FABRICATED BY USING CAD/CAM TECHNOLOGY

Comparison of retention and denture base adaptation between conventional and 3D-printed complete dentures

Effect of different framework materials on stresses induced in distal extension removable partial dentures: A strain gauge analysis

Effect of Duplication Techniques on the Fitting Accuracy of CAD-CAM Milled, 3D-Printed, and Injection-Molded Mandibular Complete Denture Bases

Effects of Selective Laser Melting Process Parameters on the Accuracy of the Intaglio Surface of Maxillary Removable Partial Denture Frameworks