Abstract:Abstract Microchannels are utilised on material surfaces of a body, allowing coolant to pass through them and enabling heat dissipation by increased contact area. Fabrication of metal surface microchannels is primarily achieved by employing a micro-milling process, which has drawbacks such as excessive cutting forces, top burrs, tool wear, and lower tool life. Alternatively, it is also realised by using Laser micro milling, which has problems associated with lower quality of surface finish, un-desired taper, heat-affected zone, and spatters. The existing literature, after due review of the current state of the art, has brought out gaps needing attention. These gaps are limited capability to reduce surface roughness, unaddressed burr width, and irregular bottom surface morphology, which affect microchannel quality. These gaps motivate this research work to improve and sustain the microchannel quality. To achieve the goals, this research work performs the fabrication of microchannels by micro-milling with automated laser assistance being achieved in two ways (a) sequentially, (b) non-sequentially, termed as LASMM and LPCMM, which are novel for the scientific community. The effects of micro milling parameters, spindle speed and feed on the quality were analysed while machining commercially pure titanium (cp-Ti). Results show that laser assistance to micro-milling provides a lower generation of undesired forces and lesser top burrs compared to micro-milling alone. In sequential laser assistance, the channels have a mean down burr width ~ 58% lower and a maximum down burr width ~ 38% lower than the channels done non-sequentially. In the case of up-burr width, a mean value ~ 60% lower and a maximum value ~ 73% lower is achieved in channels done non-sequentially as compared to those done sequentially. In the case of surface roughness, channels done sequentially have a maximum Sa value of 1.508 μm, a maximum Sq value of 1.912 μm whereas non-sequentially, they show a maximum Sa value of 3.495 μm, maximum Sq value of 4.59 μm. Steady tool wear is observed sequentially, whereas in non-sequential, rapid tool wear occurs after 500 mm of cutting length.

High throughput and low surface roughness laser layer-by-layer milling using nanosecond (ns), picosecond (ps), and hybrid ns-ps pulses: A comparative study

Laser Machining at High ∼PW/cm2 Intensity and High Throughput

Efficient ablation, further GHz burst polishing, and surface texturing by ultrafast laser

Towards obtaining high-quality surfaces with nanometric finish by femtosecond laser ablation: A case study on coppers

Exploring the machining characteristics of aluminum 6061 using nanosecond pulse fiber laser machine

Numerical and Experimental Investigation on Pulsed Nanosecond Laser Ablation Processing of Aluminum Alloy

Ablation mechanisms of nanosecond and picosecond laser scribing for metal halide perovskite module interconnection – An experimental and numerical analysis

Combination of short and ultrashort pulse laser processing for productive large scale structuring of 3D plastic mould steel

Surface ablation and threshold determination of AlCu4SiMg aluminum alloy in picosecond pulsed laser micromachining

Research and Optimization of Surface Roughness in Milling of SLM Semi-Finished Parts Manufactured by Using the Different Laser Scanning Speed

Efficient surface polishing using burst and biburst mode ultrafast laser irradiation

Micro-milling of 65 vol% SiCp/Al composites with a novel laser-assisted hybrid process

Pocket Milling of Carbon Fiber-Reinforced Plastics Using 532-Nm Nanosecond Pulsed Laser: an Experimental Investigation

Effects of laser and scanning parameters on surface modification of MONEL® alloy 400 by picosecond laser

Laser Polishing of Additive Manufactured Aluminium Parts by Modulated Laser Power

Quality enhancement of micro-milled channels with automated laser assistance

Optimization of the Effect of Laser Power Bed Fusion 3D Printing during the Milling Process Using Hybrid Artificial Neural Networks with Particle Swarm Optimization and Genetic Algorithms

Ablation and morphological evolution of micro-holes in stainless steel with picosecond laser pulses

Surface modeling and component analysis of picosecond laser ablation of CVD diamond

Parametric investigation of ultrashort pulsed laser surface texturing on aluminium alloy 7075 for hydrophobicity enhancement

Reutilization of a reflected laser beam as an effective approach for machining metallic materials with low laser absorptivity