Bio-Inspired Aggregation Control of Carbon Nanotubes for Ultra-Strong Composites

Yue Han,Xiaohua Zhang,Xueping Yu,Jingna Zhao,Shan Li,Feng Liu,Peng Gao,Yongyi Zhang,Tong Zhao,Qingwen Li

DOI: https://doi.org/10.1038/srep11533

2015-06-05

Abstract:High performance nanocomposites require well dispersion and high alignment of the nanometer-sized components, at a high mass or volume fraction as well. However, the road towards such composite structure is severely hindered due to the easy aggregation of these nanometer-sized components. Here we demonstrate a big step to approach the ideal composite structure for carbon nanotube (CNT) where all the CNTs were highly packed, aligned, and unaggregated, with the impregnated polymers acting as interfacial adhesions and mortars to build up the composite structure. The strategy was based on a bio-inspired aggregation control to limit the CNT aggregation to be sub 20--50 nm, a dimension determined by the CNT growth. After being stretched with full structural relaxation in a multi-step way, the CNT/polymer (bismaleimide) composite yielded super-high tensile strengths up to 6.27--6.94 GPa, more than 100% higher than those of carbon fiber/epoxy composites, and toughnesses up to 117--192 MPa. We anticipate that the present study can be generalized for developing multifunctional and smart nanocomposites where all the surfaces of nanometer-sized components can take part in shear transfer of mechanical, thermal, and electrical signals.

Materials Science

What problem does this paper attempt to address?

The problem that this paper attempts to solve is how to achieve high - efficiency dispersion, high - orientation arrangement and avoid aggregation of carbon nanotubes (CNT) in composites through bionic aggregation control technology, so as to prepare composites with ultra - high strength and toughness. Specifically, the authors aim to overcome the problem that carbon nanotubes are difficult to be evenly dispersed and are prone to aggregation in the polymer matrix, so as to make full use of the unique properties of carbon nanotubes, such as high strength and high conductivity.

### Main problems and challenges

1. **Aggregation problem of carbon nanotubes**:
Due to the strong van der Waals force, carbon nanotubes are easy to aggregate in the polymer matrix, which seriously affects the mechanical properties and other functional characteristics of the composites. Therefore, how to effectively control the aggregation of carbon nanotubes has become a key issue.

2. **Uniform dispersion of high - content carbon nanotubes**:
In order to achieve high - performance composites, it is necessary to achieve uniform dispersion of carbon nanotubes at a high volume fraction. This means that not only the filling amount of carbon nanotubes should be increased, but also they should be evenly distributed throughout the matrix.

3. **Enhanced interface bonding**:
The performance of composites largely depends on the interface bonding between carbon nanotubes and the polymer matrix. Good interface bonding can effectively transfer stress, thereby improving the overall performance of the material.

### Solutions

The authors proposed a bionic aggregation control strategy and achieved the above goals through the following steps:

1. **Bionic - inspired pretreatment**:
Carbon nanotubes are synthesized by injection chemical vapor deposition (CVD) and prepared into two - dimensional films. The carbon nanotubes in these films have formed an intertwined network structure, similar to the natural structure in biological composites.

2. **Polymer impregnation**:
Before stretching, a bismaleimide (BMI) resin solution with a low softening point is used to impregnate the carbon nanotube films to ensure that the surfaces of carbon nanotubes are fully covered by the polymer, thereby avoiding aggregation.

3. **Multi - step stretching**:
A multi - step stretching method is adopted to gradually stretch the impregnated films, and sufficient structural relaxation is allowed after each stretching. This method not only improves the orientation degree of carbon nanotubes, but also further reduces the aggregation phenomenon, and finally keeps the bundle structure of carbon nanotubes within 20 - 50 nm.

4. **Hot - pressing and curing**:
The stretched films are hot - pressed and cured to form the final composites. In this way, carbon nanotubes achieve high - orientation and close - arrangement in the polymer matrix while maintaining an aggregation - free state.

### Experimental results

The carbon nanotube / bismaleimide (CNT/BMI) composites prepared by the above methods exhibit extremely high tensile strength (up to 6.94 GPa), far exceeding that of traditional carbon fiber / epoxy resin composites (about 1.86 GPa). In addition, this composite also shows excellent toughness (117 - 192 MPa) and electrical conductivity.

### Summary

This research has successfully solved the problem that carbon nanotubes are difficult to be evenly dispersed and avoid aggregation in composites, providing a new approach for the development of multi - functional intelligent nanocomposites. Through bionic aggregation control technology, the authors have achieved a high - orientation and aggregation - free state of carbon nanotubes, thereby significantly improving the mechanical properties and other functional characteristics of composites.