Abstract:Background: The Accelerator Driven Subcritical System (ADS) uses a proton beam incident on a target to produce neutrons used in a nuclear reactor to process spent fuel in two ways: to accelerate its decomposition into non-radioactive waste, and to increase the rate at which it is recycled into nuclear fuel. Two cryomodules, each consisting of 7 superconducting spoke cavities, 7 superconducting magnets and 7 beam position monitors, are used to accelerate the proton beams from 3.2 MeV to 10 MeV. The superconducting magnet contains a solenoid for beam focusing and two correctors for orbit correction, it is a key component for ADS injection. Purpose: This study aims at a short superconducting magnet design to meet the required integral field strength and to reduce the leakage field at the nearby superconducting spoke cavities. The design current for the solenoid is 210 A. Methods: The main solenoid and two bucking solenoids plus the iron yoke were used to meet the leakage field requirements which is less than 1 G at a distance of 270 mm from the solenoid center. In order to shorten the magnet length to 170 mm, special design methods were taken for the magnet cryostat by removing two conflicts flanges and replacing them with the direct Al ring seal methods. A kind of conducted the current leads similar as that of Large Hadron Collider (LHC) corrector magnets was applied to the 2.1-K, 3 100-Pa cryogenic system. The small store energy magnet led to the introduction of active quench detected system, which is much more reliable. Two short magnets and two spoke cavities were installed inside a test cryomodule to test the online operation properties of the SC magnet and the SC spoke cavity. Results: A quench performance in the vertical test shows that the operating current of the solenoid magnet can reach above 300 A after natural quenching on three occasions during current ramping (260 A, 268 A and 308 A). Online operating test shows that two magnets can work at 4.2 K and 2.1 K, respectively. The quench protection system worked well when two quenches occurred as the liquid helium level decreased. Conclusion: The online operation for the two magnets confirms the physical and the mechanical design, the reliability of the quench detection technique.

Manufacturing and Testing of Accelerator Superconducting Magnets

Challenges and opportunities to assure future manufacturing of magnet conductors for the accelerator sector

Mechanical Design of Superconducting Accelerator Magnets

A Combined Testing and Modelling Methodology for the Mechanics of High-Field Superconducting Magnets

Mechanical Characterization of Low-Carbon Steels for High-Field Accelerator Magnets: Application to Nb$_{3}$Sn Low-$\beta$ Quadrupole MQXF

Fast cycling HTS based superconducting accelerator magnets: Feasibility study and readiness demonstration program driven by neutrino physics and muon collider needs

Test samples and infrastructure for accelerator magnet developments

Superconductivity for Magnets

Commissioning, Performance, and Effect of the Quench Current-boosting Device on a Dedicated Superconducting Magnet

Magnetic Design of Superconducting Magnets

Upgrade of the CERN Superconducting Magnet Test Facility

Development and Testing of the Short Superconducting Magnets for ADS Injection I

A novel device for the measurement of the mechanical and magnetic axes of superconducting magnet assemblies for accelerators

Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet with Graded Common-Coil Configuration

Development of a 1497-Mhz, 13.5-Kw Continuous- Wave Magnetron for Superconducting Radio Frequency Accelerator

Development Of Nb3sn Superconducting Coil Manufacture Technology

Mechanical Behavior of a 16-T FCC Dipole Magnet During a Quench

Optimizing the use of pressurized bladders for the assembly of HL-LHC MQXFB magnets

Efficient multiscale investigation of mechanical behavior in Nb3Sn superconducting accelerator magnet based on self-consistent clustering analysis

Design and Test of Superconducting Magnet for 200 MeV Proton Cyclotron

Mechanical Design of a Nb3Sn Superconducting Magnet System for a 45 GHz ECR Ion Source