Abstract:Background: Preservation of the remaining structures while maintaining an esthetic appearance is a major objective in removable partial prosthodontics. So, the aim of the current study was to compare the stresses induced on the supporting structures by two digitally produced esthetic core materials; Zirconia and Polyetheretherketone when used as an extracoronal attachment in distal extension removable partial dentures using strain gauge analysis. Methods: A mandibular Kennedy class II stone cast with the necessary abutments' preparations was scanned. The mandibular left canine and first premolar teeth were virtually removed. An acrylic mandibular left canine and first premolar teeth were prepared with heavy chamfer finish line and scanned. Virtual superimposition of the acrylic teeth in their corresponding positions was done. Two strain gauge slots were designed: distal to the terminal abutment and in the residual ridge. Two models and two sets of scanned teeth were digitally printed. The printed teeth were then placed in their corresponding sockets in each model and scanned. The attachment design was selected from the software library and milled out of Zirconia in the model ZR and Polyetheretherketone in the model PE. Five removable partial dentures were constructed for each model. The strain gauges were installed in their grooves. A Universal testing machine was used for unilateral load application of 100 N (N). For each removable partial denture, five measurements were made. The data followed normal distribution and were statistically analyzed by using unpaired t test. P value < 0.05 was considered to be statistically significant. Results: During unilateral loading unpaired t test showed statistically significant difference (p = 0.0001) in the microstrain values recorded distal to the abutment between the models ZR (-1001.6 µε ± 24.56) and PE (-682.6 µε ± 22.18). However, non statistically significant difference (p = 0.3122) was observed in the residual ridge between them; ZR (16.2 µε ± 4.53) and PE (15 µε ± 3.74). Conclusions: In removable partial dentures, Polyetheretherketone extracoronal attachment induces less stress on the supporting abutments compared to the zirconia one with no difference in the stresses induced by them on the residual ridge.

Effects of denture use on occlusal force on abutment teeth in molar distal-extension edentulism

Influence of mandibular free-end partial edentulism on the force exerted on maxillary anterior teeth

Clinical Measurements of Force Exerted on Anterior Teeth in Partial Edentulous Distal Extension

Force exerted on maxillary anterior teeth in mandibular unilateral and bilateral distal extension partial edentulous situation

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

Influence of rigidity of retainers on dynamic behavior of implant-supported removable partial dentures

Effect of two esthetic digitally produced materials used in fabrication of extracoronal attachments on the stresses Induced in removable partial dentures

Three-dimensional finite element analysis of implant-assisted removable partial dentures

Evaluation of Clinical Periodontal Parameters of Abutment Teeth Supporting Distal-Extension Base Removable Partial Dentures: A Cross-sectional Study

Effects of denture adhesives on denture retention and occlusal forces in complete denture wearers: A multicenter, randomized controlled trial

Analysis on the Stress of Abutment between the Uses of Two Telescope Crown Dentures to Restore Distal-extension Caused ;by Periodontal Disease

In Vitro Assessment of the Effect of Implant Position on Biomechanical Behaviors of Implant-Supported Removable Partial Dentures in Kennedy Class II Condition

Influence of a mesial cantilever on stress, strain, and axial force in fixed partial dentures with a distally tilted implant in the atrophic posterior maxilla

Stress Distribution in 5-Unit Fixed Partial Dentures with a Pier Abutment and Rigid and Nonrigid Connectors with Two Different Occlusal Schemes: A Three-Dimensional Finite Element Analysis

Effect of different framework materials on stresses induced in distal extension removable partial dentures: A strain gauge analysis

Clinical effectiveness of implant support for distal extension removable partial dentures: functional evaluation using occlusal force measurement and masticatory efficiency

A comparative finite element analysis of titanium, poly-ether-etherketone, and zirconia abutment on stress distribution around maxillary anterior implants

Four-year clinical evaluation of CAD/CAM indirect resin composite premolar crowns using 3D digital data: Discovering the causes of debonding

Effect of build orientation on the wear resistance and hardness of denture teeth fabricated using digital light processing: An in vitro study

Effect Of Central Retainer Shape And Abduction Angle During Preparation Of Teeth On Dentin And Cement Layer Stress Distributions In Endocrown-Restored Mandibular Molars

Mechanical Influence of Edentulous Mandibular Morphology on Peri-implant Bone in Implant Prosthetics: Threedimensional Finite Element Analysis