Abstract:Nanosized copper oxide-zirconia particles containing 10-30 mol% of copper were prepared by using a precipitation technique in aqueous tetramethylammonium hydroxide solutions. Two methods, in situ (INS) and step-by-step (SBS), which differed in the time when the copper salt was introduced to the synthesis procedure, were used, and this allowed a comparison of the properties of the final powders produced using the two modes of preparation. The surface areas and phase compositions were different for the samples prepared from the two different methods after calcination at 500 degreesC. A surface area of 168 m(2) g(-1) was obtained for the sample prepared with the SBS method and 121 m(2) g(-1) for the INS method, both contain 30 mol% copper. Tetragonal ZrO2 was observed from X-ray diffraction patterns for all samples prepared with the SBS method, however, no separate phase of copper or copper oxide was observed. It is proposed that all of the copper is finely distributed on the surface of the ZrO2 particles with the SBS method. For the samples prepared from the INS method, tetragonal ZrO2 was obtained at a low copper content and the peaks indexed to tetragonal ZrO2 shifted to higher angle with the increase of copper content, indicating copper ions being incorporated into the lattice. An amorphous compound was obtained at high copper content (30 mol%). The phase change with the calcination temperature was also investigated for the INS sample containing 30 mol% copper. The studies show that tetragonal ZrO2 and copper oxide were present after calcination at 400 degreesC, and tetragonal ZrO2 with a small amount of monoclinic ZrO2, as well as copper oxide, formed after calcination at 700 degreesC. However, after heating at 500 degreesC, amorphous compounds were obtained, suggesting that 500 degreesC could be a phase transition point. The incorporation of copper in the ZrO2 lattice resulted in a loss of order in the ZrO2 structure when calcined at 500 degreesC, with a further increase in the calcination temperature leading to the phase change.

Deposition time effect on copper oxide nano structures, an analysis study using chemical method

Effect of solution concentration on surface morphology, chemical composition and photoresponse of CuO/Cu 2 O composite thin films grown by hydrothermal synthesis

Influence of Interphase Distribution of Reactants on Preparation of Nano-CuO by Adsorption Phase Technique

Effect of Electrodeposition Time on Microstructure, Wettability and Optical Properties of ZnO Nanorod Arrays

Temperature and time dependent morphological evolution of solution phase synthesized copper oxide nanostructures

Synthesis and Characterization of Copper Oxide Nanoparticles by Solution Evaporation Method

Study on Preparation of Copper Oxide Nanopowders

Influence Different Substrates on the Sensing Performance of Copper Oxide Thin Films Synthesis via the Hydrothermal Method

Study of Deposition Temperature Effect on Spray-Deposited Copper Oxide Thin Films and Its Schottky Diodes

Preparation of Nano Cuprous Oxide by Ball Milling in Water Solution

Fabrication and Characterization of Novel Nanostructured Copper Oxide Films Via A Facile Solution Route

The effect of ultrasonic irradiation power and initial concentration on the particle size of nano copper(II) coordination polymer: Precursors for preparation of CuO nanostructures

Effects of Rapid Heat Treatments on the Properties of Cu2O Thin Films Deposited at Room Temperature Using an Ammonia-Free SILAR Technique

Preparation and Characterization of CuO Nanostructured Thin Films by Chemical Bath Deposition

Preparation and Characterization of Copper Oxide Nanoparticles Through Solid State Thermal Decomposition of an Aqua Nitrato Copper(II) Complex with a Tridentate Schiff-base Ligand as a New Precursor

Preparation and characterization of CuO–ZrO2 nanopowders

Copper nanocubes and nanostructured cuprous oxide prepared by surfactant-assisted electrochemical deposition

Study of the structural, optical, electrical and electrochemical properties of copper oxide thin films synthesized by spray pyrolysis

Effect of Cu(OH)2 decomposition method on figure of nano-CuO

Spectroscopic characteristics of highly pure metal oxide nanostructures prepared by DC reactive magnetron sputtering technique

Fabrication and optical property of nano-sized cupric oxide films