Abstract:To support future ITER operation, experimental campaigns at the Joint European Torus (JET) with an ITER-like wall (tungsten divertor and beryllium main chamber) in pure deuterium (D), tritium (T) and Deuterium-Tritium (D-T) were performed. One of the most important challenges in recent years was the development of two main scenarios that investigated different approaches to achieve the high fusion power as well as good plasma confinement (Garzotti et al., 2023). The first one, so-called baseline scenario is relying on high plasma current (I p ≈3.5 MA), normalized beta β N < 2 and safety factor q 95 ≈ 3 (Garzotti et al., 2023). On the other hand, the second one, so-called Hybrid scenario is operating at lower plasma current (flat-top I p ≤ 2.6 MA) and density with respect to the baseline, higher normalized beta β N > 2 and safety factor q 95 ≈ 4.8 (Hobirk et al., 2023). In this paper we focus on the impurity behaviour analysis for the baseline discharges at I p = 3.5 MA and B T = 3.3 T with D, T and DT plasmas, in which the gas and power waveform were optimized to achieve the best possible performance. In particular, we study the impact of total heating power (P tot + P alpha ), flat-top gas flow and ELM (edge localized modes) frequency on mid-Z (Nickel (Ni), Copper (Cu)) and high-Z (Tungsten (W)) impurities. In addition, we compared the two best performing pulses of the baseline scenario (I p = 3.5MA, B T = 3.3 T and P in ≈ 35 MW) in D and DT in order to identify the causes responsible for the increase in radiation during the DT pulse, which led to an early plasma termination. All presented results rely on the data collected by the VUV as well as the bolometry system. Detailed analysis indicates that in the baseline scenario, higher radiation, which is most likely due to the tungsten (W), is observed for T and DT plasmas in comparison to D. Moreover, for the two best performing baseline pulses, tomographic reconstructions show that the radiated power density is mainly emitted from the low field side (LFS) of the plasma and W does not accumulate in the plasma center (Telesca et al., 2024).

ILC Extraction Line Simulations with TDR Parameters

NLC Beam Properties and Extraction Line Performance with Beam Offset at IP

The International Linear Collider Technical Design Report - Volume 4: Detectors

Beam Simulation Studies of ECR Beam Extraction and Low Energy Beam Transport for FRIB.

Optimizing Beam-Ion Confinement in ITER by Adjusting the Toroidal Phase of the 3D Magnetic Fields Applied for ELM Control

ILC Main Linac Alignment Simulations using Conventional Techniques and the Rapid Tunnel Reference Survey Model (RTRSM)

The International Linear Collider Technical Design Report - Volume 2: Physics

Beam Dynamics Design and Error Study of BISOL Deuteron Driver Linac

Radiation damage of the ILC positron source target

Ripple effect and impact of test blanket module by using RAFM steels on the plasma of ITER

Insights into stripping losses of negative ions in an ITER-like pre-acceleration system

Beam Dynamics Studies at the PIP-II Injector Test Facility

Investigation on Current Loss of High-Power Vacuum Transmission Lines with Coaxial-Disk Transitions by Particle-in-cell Simulations

Studies on the Electron Reconstruction Efficiency for the Beam Calorimeter of an ILC Detector

Power deposition studies for standard and crystal-assisted heavy ion collimation inthe CERN Large Hadron Collider

Status Report on the Hydrodynamic Simulations of a Tapered Plasma Lens for Optical Matching at the ILC $e^+$ Source

The Next Linear Collider Extraction Line Design

Reconstructing long-lived particles with the ILD detector

COREDIV simulations of D and D-T high current-high power Baseline pulses in JET-ITER Like Wall

Beam Loss Monitoring with Fixed and Translating Scintillation Detectors Along the Fermilab Drift-tube Linac

Impurity behaviour in JET high-current baseline scenario for Deuterium, Tritium and Deuterium-Tritium plasmas