Abstract:Isostructural alloying has been regarded as an important approach to boosting thermoelectric performance of narrow gap semiconductors through thermal conductivity reduction. However, it does harm to carrier mobilities as well because of atomic disorders. Here, we extend the alloying concept from "isostructural" to "quasi-isostructural", which means that the two alloying components are no longer strictly isostructural but structurally closely related. As a proof-of-concept, a series of cubic Cu2SnSe3–tetragonal Cu3SbSe4 quasi-isostructural alloys (Cu2+xSn1–xSbxSe3+x) were synthesized, and their thermoelectric transport properties were systematically studied. No significant loss of carrier mobilities was found during quasi-isostructural alloying, probably due to the structural similarity of the two end members as well as the negligible mass contrasts between Sn and Sb. Surprisingly, a remarkable reduction of lattice thermal conductivity from 1.2 W m–1 K–1 for Cu2SnSe3/Cu3SbSe4 to 0.4 W m–1 K–1 for Cu5SnSbSe7 at 673 K was observed, which can hardly be explained from a solid solution perspective. Our X-ray photoelectron spectroscopy analysis unambiguously demonstrate the coexistence of Sn2+ and Sn4+ in the alloying systems, whereas Sn simply exhibits Sn4+ in Cu2SnSe3. We deduce that the minute structural changes of Cu2SnSe3 during quasi-isostructural alloying make Sn discordant, leading to its valence state splitting. The mixed-valence scattering therefore strongly impedes phonon propagation beyond alloying. Altogether, a considerably enhanced ZT ≈ 0.4 is realized in the sample with x = 0.2, which is 150% improvement over the x = 0 sample. By selecting the x = 0.5 sample as a representative, a preliminary doping study was performed but seems unsuccessful because of the varying Sn2+/Sn4+ ratio. We expect higher thermoelectric performance in those quasi-isostructural alloys if their carrier concentration can be fully optimized.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c01155?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c01155</a>.Temperature-dependent heat capacity (Cp), thermal diffusivities (D) and Lorenz number (L) for Cu2+xSn1–xSbxSe3+x (x = 0, 0.2, 0.5, 0.8, and 1.0). The longitudinal (νl) and transverse (νt) acoustic velocities, calculation of average acoustic velocity (vs) (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c01155/suppl_file/ae1c01155_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Band flattening and phonon-defect scattering in cubic SnSe–AgSbTe2 alloy for thermoelectric enhancement

Enhanced thermoelectric perfromance in cubic form of SnSe stabilized through enformatingly alloying AgSbTe2

Boosting thermoelectric performance of SnTe by selective alloying and band tuning

Strong lattice anharmonicity securing intrinsically low lattice thermal conductivity and high performance thermoelectric SnSb2Te4 via Se alloying

Enhancement of Thermoelectric Performance of Layered SnSe2 by Synergistic Modulation of Carrier Concentration and Suppression of Lattice Thermal Conductivity

Band convergence and nanostructure modulations lead to high thermoelectric performance in SnPb0.04Te-y% AgSbTe2

Polycrystalline SnSe–Sn1–vS Solid Solutions: Vacancy Engineering and Nanostructuring Leading to High Thermoelectric Performance

Interstitial Defects Facilitate Dense Dislocations and Band Convergence for High Thermoelectric Performance in SnTe

Improved Solubility in Metavalently Bonded Solid Leads to Band Alignment, Ultralow Thermal Conductivity, and High Thermoelectric Performance in SnTe

Modulating structures to decouple thermoelectric transports leads to high performance in polycrystalline SnSe

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect

Nanocrystal-based thermoelectric SnTe-NaSbSe 2 alloys with strengthened band convergence and reduced thermal conductivity

High-Performance SnTe Thermoelectric Materials Enabled by the Synergy of Band Convergence and Phonon Scattering

Enhancing the thermoelectric performance of SnTe-CuSbSe 2 with an ultra-low lattice thermal conductivity

Cubic phase stabilization and thermoelectric performance optimization in AgBiSe 2 –SnTe system

Anionic regulation and valence band convergence boosting the thermoelectric performance of Se-alloyed GeSb 2 Te 4 single crystal

Advancing thermoelectrics by vacancy engineering and band manipulation in Sb-doped SnTe–CdTe alloys

Atomic-scale structure and thermoelectric properties in medium-entropy PbSnTeSe alloy

Contrasting Thermoelectric Properties in cubic SnSe-NaSbSe 2 and SnSe-NaSbTe 2 : High Performance Achieved via Increasing Cation Vacancies and Charge Densities

Quasi-isostructural Alloying of Cu 2 SnSe 3 –Cu 3 SbSe 4 toward Higher Thermoelectric Performance

Metavalent Bonding in Cubic SnSe Alloys Improves Thermoelectric Properties over a Broad Temperature Range