Abstract:SnSe crystals have been discovered as one of the most efficient thermoelectric materials due to their remarkable thermal and electrical transports. But the polycrystalline SnSe possesses much lower performance especially for the low carrier mobility and electrical conductivity. We firstly attempted to explain and verify the difference in the electrical conductivity as a function of temperature between p-type crystalline and polycrystalline SnSe by considering the grain boundary effects in the polycrystalline samples. On the basis of 2% Na doping to optimize the carrier concentration, the carrier mobility is improved by further introducing In, leading to enhanced carrier mobility from 3 to 9 cm2·V−1·s−1 in polycrystalline SnSe. Moreover, In doping introduces extra resonant levels in SnSe, which increases the density of states near Fermi level and leads to an enhanced band effective mass. Large Seebeck coefficient of ~ 205 μV·K−1 at 300 K and maximum power factor of ~ 7.5 μW·cm−1·K−2 at 773 K can be obtained in the Sn0.975Na0.02In0.005Se sample, leading to a competitively high dimensionless figure of merit (ZT) value exceeding 1.1 at 773 K.摘要晶体 SnSe 由于出色的电声传输性能, 不断表现出优异的热电特性。但是, 相对于晶体, 多晶 SnSe 的电导率和载流子迁移率呈现数量级的降低。首先, 我们试图通过考虑多晶样品中晶界的影响来解释 p 型晶体 SnSe 和多晶 SnSe 的电导率随温度变化的差异。通过掺杂 2% 的 Na 来优化多晶 SnSe 的载流子浓度, 在此基础上引入 In 提高了基体的载流子迁移率, 样品的室温迁移率由 3 cm2·V-1·s-1增加到 9 cm2·V-1·s-1。此外, 通过在多晶 SnSe 中掺杂 In 引入了额外的共振能级, 增加了费米能级附近的态密度, 提高了能带有效质量。引入 In 之后, Sn0.975Na0.02In0.005Se样品在 300 K 时的塞贝克系数从 ~ 137提高到 ~ 205 μ V·K-1, 在 773 K 时的最大功率因子从 ~ 3.9提高到 ~ 7.5 μ W·cm-1·K-2, 使热电优值 (ZT) 在 773 K 时超过了 1.1Graphical Abstract

Modulating structures to decouple thermoelectric transports leads to high performance in polycrystalline SnSe

Modulating Structures to Decouple Thermoelectric Transport Leads to High Performance in Polycrystalline SnSe

Enhancement of Thermoelectric Performance of Layered SnSe2 by Synergistic Modulation of Carrier Concentration and Suppression of Lattice Thermal Conductivity

High thermoelectric efficiency realized in SnSe crystals via structural modulation

Enhanced thermoelectric perfromance in cubic form of SnSe stabilized through enformatingly alloying AgSbTe2

Thermoelectric transport properties of polycrystalline SnSe alloyed with PbSe

Introducing PbSe quantum dots and manipulating lattice strain contributing to high thermoelectric performance in polycrystalline SnSe

Realizing High Thermoelectric Performance of Ag/Al Co‐Doped Polycrystalline SnSe through Band Structure Modification and Hydrogen Reduction

Modulating Electrical Transport Properties of SnSe Crystal to Improve the Thermoelectric Power Factor by Adjusting Growth Method

High thermoelectric properties realized in polycrystalline (Ag, Ga) Co-doped SnSe via two-steps point defects modulation

Polycrystalline SnSe–Sn1–vS Solid Solutions: Vacancy Engineering and Nanostructuring Leading to High Thermoelectric Performance

Realizing High In-plane Carrier Mobility in N-type SnSe Crystals through Deformation Potential Modification

Achieving high thermoelectric performance with Pb and Zn codoped polycrystalline SnSe via phase separation and nanostructuring strategies

Lattice Strain Leads to High Thermoelectric Performance in Polycrystalline SnSe

Enhanced thermoelectric performance of AgCuTe-doped polycrystalline SnSe by lattice plainification

Realizing High Thermoelectric Performance in p-Type SnSe Crystals via Convergence of Multiple Electronic Valence Bands

Realizing high thermoelectric properties in p-type polycrystalline SnSe by inducing DOS distortion

Enhanced Density of States Facilitates High Thermoelectric Performance in Solution-Grown Ge- and In-Codoped SnSe Nanoplates

Improved thermoelectric properties of n-type polycrystalline SnSe via carrier concentration optimization

Realizing excellent thermoelectric performance in Ag-doped Cu 2 SnSe 3 -ZnSe solid solution by symmetry modification and stacking promotion

Anionic regulation and valence band convergence boosting the thermoelectric performance of Se-alloyed GeSb 2 Te 4 single crystal