Abstract:Background: Pencil Beam Scanning proton therapy has many advantages from a therapeutic point of view, but raises technical constraints in terms of treatment verification. The treatment relies on a large number of planned pencil beams (PB) (up to thousands), whose delivery is divided in several low-intensity pulses delivered a high frequency (1 kHz in this study). Purpose: The purpose of this study was to develop a three-dimensional quality assurance system allowing to verify all the PBs' characteristics (position, energy, intensity in terms of delivered monitor unit-MU) of patient treatment plans on a pulse-by-pulse or a PB-by-PB basis. Methods: A system named SCICOPRO has been developed. It is based on a 10 × 10 × 10 cm3 scintillator cube and a fast camera, synchronized with beam delivery, recording two views (direct and using a mirror) of the scintillation distribution generated by the pulses. A specific calibration and analysis process allowed to extract the characteristics of all the pulses delivered during the treatment, and consequently of all the PBs. The system uncertainties, defined here as average value + standard deviation, were characterized with a customized irradiation plan at different PB intensities (0.02, 0.1, and 1 MU) and with two patient's treatment plans of three beams each. The system's ability to detect potential treatment delivery problems, such as positioning errors of the treatment table in this work (1° rotations and a 2 mm translation), was assessed by calculating the confidence intervals (CI) for the different characteristics and evaluating the proportion of PBs within these intervals. Results: The performances of SCICOPRO were evaluated on a pulse-by-pulse basis. They showed a very good signal-to-noise ratio for all the pulse intensities (between 2 × 10-3 MU and 150 × 10-3 MU) allowing uncertainties smaller than 580 µm for the position, 180 keV for the energy and 3% for the intensity on patients treatment plans. The position and energy uncertainties were found to be little dependent from the pulse intensities whereas the intensity uncertainty depends on the pulses number and intensity distribution. Finally, treatment plans evaluations showed that 98% of the PBs were within the CIs with a nominal positioning against 83% or less with the table positioning errors, thus proving the ability of SCICOPRO to detect this kind of errors. Conclusion: The high acquisition rate and the very high sensitivity of the system developed in this work allowed to record pulses of intensities as low as 2 × 10-3 MU. SCICOPRO was thus able to measure all the characteristics of the spots of a treatment (position, energy, intensity) in a single measurement, making it possible to verify their compliance with the treatment plan. SCICOPRO thus proved to be a fast and accurate tool that would be useful for patient-specific quality assurance (PSQA) on a pulse-by-pulse or PB-by-PB verification basis.

Characterization and performances of a monitoring ionization chamber dedicated to IBA-universal irradiation head for Pencil Beam Scanning

An in-vivo treatment monitoring system for ion-beam radiotherapy based on 28 Timepix3 detectors

Beam monitor chamber calibration of a synchro-cyclotron high dose rate per pulse pulsed scanned proton beam

A prototype scintillating fibre beam profile monitor for Ion Therapy beams

A Multi-Layer Strip Ionization Chamber (MLSIC) Device for Proton Pencil Beam Scan Quality Assurance.

Proton 3D dose measurement with a multi-layer strip ionization chamber (MLSIC) device

A Beam Monitor for Ion Beam Therapy Based on HV-CMOS Pixel Detectors

Experimental comparison of cylindrical and plane parallel ionization chambers for reference dosimetry in continuous and pulsed scanned proton beams

Implementation of an ionization chamber array for linear accelerator monthly dosimetry QA

Development of a three-dimensional scintillation detector for pencil beam verification in proton therapy patient-specific quality assurance

Medipix3 for dosimetry and real-time beam monitoring: first tests at a 60 MeV proton therapy facility

Investigation of Ionization Chamber Characteristics for Ultrahigh-dose-rate Scanned Carbon-ion Beams

Geometrical Characterization of an Inorganic Scintillator Detector for Proton Therapy Using a Micrometer-Scale Ion Beam

A High Performance Scintillator Ion Beam Monitor

Development of novel ionization chambers for reference dosimetry in electron FLASH radiotherapy

Evaluation of ion chamber response for applications in electron FLASH radiotherapy

Feasibility of using a transmission ion chamber for QA tests of medical linear accelerators

Impact of Measurement Conditions and Design Features of IBA Detectors on the Small Radiation Fields Output Factors

An integrated system for measuring 3D dose distributions of carbon-ion pencil beams in regular QA practice

Characterization of a Low-Cost Plastic Fiber Array Detector for Proton Beam Dosimetry