Abstract:The performance of superconducting magnets is greatly dependent on the size and uniformity of the superconducting filaments within the wire. However, in the fabrication of Bi 2 Sr 2 CaCu 2 O x (Bi2212) wires using ceramic oxide as the superconducting filaments, we face multiple challenges including filament fragility, poor uniformity, and non-smooth Ag/superconductor interfaces. These challenges primarily stem from the significantly lower plastic deformation capability of ceramic oxide powder filaments compared to metal matrices. To address these challenges, this study focuses on the modification of ceramic oxide precursor powders. Through the utilization of low-temperature, low oxygen partial pressure ( p O 2 ) heat treatment, we have observed significant changes in the Cu chemical states and lattice parameters within the Bi2212 grains. These alterations have proven to be highly effective in reducing the energy required for grain sliding and, in turn, enhancing the plastic deformation properties of the Bi2212 oxide filament. Furthermore, post-annealing the oxide powder under low p O 2 conditions narrows the gap in plastic deformability between the Ag sheath and the oxide filaments, resulting in improved filament uniformity and a smoother Ag/oxide interface in Bi2212 wires. Notably, the Bi2212 grains exhibit an orderly arrangement within the wires. As a result of these improvements, the critical current density ( J c ) of the final wires increases by an impressive 70 %. The outcomes of this study are not only crucial for producing Bi2212 magnets with higher magnetic field strength, improved magnetic field uniformity, and enhanced operational stability, but also offer fresh insights and methodologies for advancing the field of superconducting materials.

Performance of Titanium-Oxide/Polymer Insulation in Bi-2212/Ag-alloy Round Wire Wound Superconducting Coils

Characterization of insulating coatings for wind-and-react coil fabrication

Performance and Microstructure of Bi-2212 Wire under Different OverPressures Heat-treatment

Development of a persistent superconducting joint between Bi-2212/Ag-alloy multifilamentary round wires

Development of persistent joints for superconducting Bi-2212 coils

Axial Tensile Stress-Strain Characterization Of Bi-2212 Round Wire With Different Heat Treatments

Critical current of Bi-2212 round wires with different heat treatment conditions

Performance of First Bi-2212 Cable with Pre-over Pressure and over Pressure Heat Treatment

Synergic realization of electrical insulation and mechanical strength in liquid nitrogen for high-temperature superconducting tapes with ultra-thin acrylic resin coating

Influence of Torsional Strain on the Bi-2212 Tapes and Round Wires under Background Field

Synergistic Effects of Micro-hBN and Core-Shell Nano-TiO2@SiO2 on Thermal and Electrical Properties of Epoxy at High Frequencies and Temperatures

Research On The Mechanical Properties Of Jacket Used For Bi-2212 Cable-In-Conduit Conductor

Research on Insulation Technology for Nb3Sn Layer Coil of Superconducting Conductor Testing Facility

33.8 TESLA WITH A YBa2Cu3O7−xSUPERCONDUCTING TEST COIL

Enhancement of high-temperature superconducting coil stability using doped smart insulation materials for superconducting magnet applications

Development of a Bi-2212 Solenoid Insert Coil in a 12 T Superconducting Magnet

Experiment of Joints Resistance and Critical Current of Bi2212 Conductor

Comparative study on the critical current performance of Bi-2223/Ag and YBCO wires in low magnetic fields at liquid nitrogen temperature

Improvement of plastic deformation property and current carrying capacity of Bi2212 wires through low oxygen partial pressure post-annealing of precursor

Fabrication and Characterization of Ni-clad Bi-2223/Ag Superconducting Tapes

Development of radiation-resistant magnet coils for high-intensity beam lines. II. Completely inorganic insulated coils