Abstract:Dissimilar metal weld joints (DMWJ) widely exist in the nuclear power plants to join the different parts which are made of different structural materials. Among these DMWJs, safe-end DMWJ has attracted much attention of researchers and operating enterprises, as premature failures, mainly stress corrosion cracking failures, have occurred in these kinds of joints. However, DMWJ with 52M as filler metal in the nuclear power plants has no in-service experience. To ensure the structural integrity of the weld joint and the safe operation of the future plants, the microstructure and local properties of a domestic safe-end DMWJ by using hot-wire gas tungsten arc welding (GTAW) technology was studied in detail by OM, SEM, micro-hardness testing, local mechanical tensile testing and slow strain rate tests. The tensile tests were performed at room temperature with the tensile speed of 5 mu m/s while the slow strain rate tests were conducted in simulated primary water containing 1500 mg/L B as H3BO3 and 2.3 mg/L Li as LiOH with 2 mg/L dissolved oxygen at 325 degrees C. A large amount of type I boundaries and type II boundaries which are susceptible to stress corrosion cracking (SCC) exist in 52Mb near the SA508/52Mb interface and result in the highest SCC susceptibility of this interface. Microstructure transition was found in the SA508 heat affected zone (HAZ). In 316LN HAZ, increasing the distance from the fusion boundary, the number fraction of CSL boundaries increase while the residual strain decreases, resulting in the second-highest SCC susceptibility of 316LN HAZ. In 52M, residual strain distributes randomly but not uniformly, the residual strain is prone to accumulate at the grain boundaries. Dramatic changes of mechanical properties are observed across the joint, especially at the SA508/52M interface. The differences of the local microstructure and chemical composition lead to the differences of the local properties of the weld joint.

Analysing suspected linear indications in narrow-gap welding of nuclear power plants via radiographic inspection

Study on Industrial Computed Tomography Detection and Identification of Inclusion Defects in Thick-Wall Polyethylene Pipe Butt Fusion Joint Within Nuclear Power Plant

Cause Analyses of the Weld Seam Cracks of a Prehydrogenating Reactor

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Study on Porosity Defect Detection in Narrow Gap Laser Welding Based on Spectral Diagnosis

Microstructure quantification and phased array ultrasonic inspection of GH3535 alloy weld

Welding defect detection in nuclear power plant spent fuel pool panels based on alternating current field measurement: experimental and finite element analysis

Microscopic Analysis of Intergranular Corrosion of 316L Stainless Steel

Analysis for a crack of the manhole in a reactor of Ethidene Diamine unit

Failure Analysis on Unexpected Fracture of the Hydraulic Expansion Mandrel for Tube to Tubesheet Expanding in the Steam Generator of Nuclear Power Plant

Prediction of static failure in metal inert gas welded nuclear grade pipe 347 SS: Experimentation and finite-element analysis approach

The Defects and Microstructure in the Fusion Zone of Multipass Laser Welded Joints with Inconel 52m Filler Wire for Nuclear Power Plants

In-situ observations on local fracture behavior in a dissimilar metal weld joint of nuclear power plant

In-situ investigation of microstructure-dependent deformation behavior of an electron-beam welded Ni Co based superalloy

Failure analysis of leaking firefighting pipeline used in nuclear power plant: Corrosion development process and key influence factors

Development of microstructure and residual stress in electron beam welds in low alloy pressure vessel steels

Local fracture behavior in an Alloy 52M dissimilar metal welded joint in nuclear power plants

Metallurgical investigation of electron beam welded duplex stainless steel X2CrNiMoN22-5-3 with plasma nitrided weld edge surfaces

Process Stability and Parameters Optimization of Narrow-Gap Laser Vertical Welding with Hot Wire for Thick Stainless Steel in Nuclear Power Plant

Microstructure and Local Properties of a Domestic Safe-End Dissimilar Metal Weld Joint by Using Hot-Wire GTAW

Comparative Study of Microstructure and Properties of Low-Alloy-steel/nickel-based-alloy Interfaces in Dissimilar Metal Weld Joints Prepared by Different GTAW Methods