Abstract:Micro-interconnection copper pillar bumps are being widely used in the packaging areas of memory chip and high performance computer due to their high density, good conductivity and low noise. Studying the interfacial behavior of copper pillar bump is of great significance for understanding its failure mechanism and microstructure evolution in order to improve the reliability of flip chip package. The thermoelectric stress test, in-situ monitor, infrared thermography test, and microstructure analysis method are employed to study the interfacial reaction, life distribution, failure mechanism and their effect factors of Cu/Ni/SnAg1.8/Cu flip chip copper pillar interconnects under 9 groups of thermoelectric stresses including 2104-3104 A/cm2 and 100-150°C. Under thermoelectric stresses, the interfacial reaction of Cu pillar can be divided into three stages:Cu6Sn5 growth and Sn solder exhaustion; the Cu6Sn5 phase transformation, exhaustion and the Cu3Sn phase growth; voids formation and crack propagation. The rate of Cu6Sn5 phase transforming into Cu3Sn phase is positively correlated with the current density. There are four kinds of failure modes including Cu pad consumption, solder complete consumption and transformation into Cu3Sn, Ni plating layer erosion and strip voids. An obvious polar effect is observed during the dissolution of Cu pads on the substrate side and the Ni layer on the Cu pillar side. When Cu pad is located at the cathode, the direction of electron flow is the same as that of the heat flow, and it can accelerate the consumption of Cu pad and the growth of Cu3Sn. When Ni layer serves as the cathode, the electron flow can enhance the consumption of Ni layer. Under 150°C and 2.5104 A/cm2, the local Ni barrier layer is eroded after 2.5 h, which results in the transformation of Cu pillar on the Ni side into (Cux, Niy)6Sn5 and Cu3Sn alloy. The life of Cu pillar interconnection complies well to the 2-parameter Weibull distribution with a shape parameter of 7.78, which is a typical characteristic of cumulative wear-out failure. The results show that the intermitallic growth behavior and failure mechanism at Cu pillar interconnects are significantly accelerated and changed under thermoelectric stresses compared with the scenario under the single high temperature stress.

Microstructure and growth of Cu hillock on redistribution line under electromigration

Characterization of electromigration-induced short-range stress development in Al(0.25 at. % Cu) conductor line

Understanding the Impact of Surface Engineering, Structure, and Design on Electromigration Through Monte Carlo Simulation and In‐Situ SEM Studies

Atomic-Scale Investigation of Electromigration with Different Directions of Electron Flow into High-Density Nanotwinned Copper through In Situ HRTEM

Comparison of the Time-Dependent Physical Processes in the Electromigration of Deep Submicron Copper and Aluminum Interconnects

Crystalline Orientation Effect of Single-Grain Sn-Rich Cu Pillar Bumps on Electromigration Lifetime

Reliability Study of Fine Pitch Cu-Sn Micro-Bump Structure Electromigration Test by Finite Element Simulation

Control and Regulation of Au Hillocks Growth by the Electrical Field and Their Metastable Dynamics in Ambient Atmosphere

Effect of Bonding Strength on Electromigration Failure in Cu–Cu Bumps

Electromigration behavior of 60 nm dual damascene Cu interconnects

Electromigration reliability issues in dual-damascene Cu interconnections

Electrical transport characteristics of atomic contact and nanogap dynamically formed by electromigration

The Study of the Reliability of Complex Components during the Electromigration Process

The In-Situ Observation of Grain Rotation and Microstructure Evolution Induced by Electromigration in Sn-3.0Ag-0.5Cu Solder Joints

Electric Current-Induced Abnormal Cu/γ-InSn4 Interfacial Reactions

Interfacial reaction and failure mechanism of Cu/Ni/SnAg1.8/Cu flip chip Cu pillar bump under thermoelectric stresses

Surface protrusion induced by inter-diffusion on Cu-Sn micro-pillars

Electric Current-Induced Abnormal Cu/γ-InSn 4 Interfacial Reactions

Microstructure of Cold Rolled Single Crystal Cu

Thermomigration-induced failure in ball grid array solder joint under high current stressing

Crossover between Re-Nucleation and Dendritic Growth in Electrodeposition without Supporting Electrolyte