Abstract:Amplitude-modulated (AM) harmonic motion imaging (HMI) is one of the radiation-force-based techniques, which has the capability of imaging tissue mechanical properties during the application of the acoustic radiation force. Since only displacement images have been presented until now, the theory between tissue displacement and modulus in AM-HMI has not been validated. Here, a finite-element model (FEM) is used to accurately model the dynamic response in tissue mimicking phantoms to evaluate HMI performance. The FEM and experimental results of phantoms with the same stiffness variations are compared and used to describe the behavior of tissue during the application of the stimulus. A harmonic force was generated by a 4.68 MHz single-element focused ultrasound (FUS) transducer. Since the focus is highly localized and has a harmonic response from AM beam, the motion characteristics can be directly related to the regional tissue modulus. The resulting motion was imaged simultaneously using a diagnostic (pulse-echo) transducer at center frequency of 7.5 MHz. RF signals were acquired using a standard pulse-echo technique with a PRF of 5.4 kHz. ID cross-correlation technique was performed to estimate the resulting axial displacement. In the FEM simulation, a rectangular mesh with dimensions of 35 mm in the axial and 30 mm in the lateral directions was generated. There were a total of 2771 nodes and 5424 triangular elements in the mesh. For simplicity, the mesh was assumed to be a purely elastic medium with Young's modulus of 10 kPa. The acoustic pressure field was simulated in Field II using the same transducer parameters as in the experiment. This pressure field was used as the excitation force to generate displacements. The imaging field was simulated in Matlab 7.2 using a 2D convolutional image formation model with 128 acoustic elements, a center frequency of 7.5 MHz and 40 MHz sampling frequency. Only the displacement estimation at the center RF lines was considered i- n the validation with the single-element pulse-echo transducer used in the experiments. A good agreement between the results from the FEM and experiment findings was observed in phantom study. Finally, in vivo application is presented.

Characterization of MEMS transducer performance using near-field scanning interferometry

The design and test of MEMS piezoresistive ultrasonic sensor arrays

Effect of Shared Cavity on Electromechanical Performance of Piezoelectric Based Micro-machined Ultrasonic Transducer Array.

Design and simulation of a 2-D array flexible ultrasound transducer system for tissue characterization – A pilot study

Performance and Crosstalk Evaluation of 2-D Array Piezoelectric Micromachined Ultrasonic Transducer with 3-D Finite Element Simulation

Acoustic Transmission Measurements for Extracting the Mechanical Properties of Complex 3D MEMS Transducers

Design Optimization of Surface Acoustic Wave Devices and Investigation of Fabricated Devices under Temperature, Humidity and Steam Environments

Modeling and Optimization of CMUTs Arrays for Improved Transmission and Reception Performance in Immersion

Integrated Measurement Of Micro Motions For Mems Dynamic Performance Analysis

Ultrasonic Transducer Array Design For Medical Imaging Based On Mems Technologies

Design and simulation of high-frequency (>100 MHz) ultrasonic phased array transducer

Stroboscopic Interferometer for Dynamic MEMS Characterization

Acoustic Field Characterization of Medical Array Transducers Based on Unfocused Transmits and Single-Plane Hydrophone Measurements

Round-Trip Sensitivity-Bandwidth Optimization and Characterization of High-Frequency PMUTs

Design and Characterization of High-Density Ultrasonic Transducer Array

Vertical Scanning White-Light Interferometry for Dimensional Characterization of Microelectromechanical System Devices

Optical Fourier Transform Based In-Plane Vibration Characterization for MEMS Comb Structure

Non-Contact Mechanical Testing and Characterization of Micro-Scale Structures

Health Monitoring of Single-Element Piezoelectric Transducer Using Its Electromechanical Admittance

Performance analysis of FEM simulated different shaped membranes based capacitive MEMS sensor

9C-5 2D Simulation of the Harmonic Motion Imaging (HMI) with Experimental Validation