Abstract:The significant disparities in physical and chemical properties between aluminum alloy and high-strength steel pose substantial challenges for conventional friction joining techniques. To address this issue, this study proposes a novel approach utilizing inertial friction welding with an interlayer to join these dissimilar materials. A CrCoNi medium entropy alloy sheet was selected as the interlayer due to its intermediate melting point, thermal conductivity, strength, and surface hardness between 6061-T6 aluminum alloy and 42CrMo steel, as well as its high element mixing entropy. These properties were deemed crucial for balancing interface heat generation and regulation the formation of intermetallic compounds. The experimental procedure involved embedding the CrCoNi sheet into the end face of the 6061-T6 aluminum alloy, followed by the application of IFW to join the aluminum alloy with 42CrMo high-strength steel. This investigation focuses on examining the effects of three distinct friction speeds (3800, 4000, and 4200 rpm) on the microstructural characteristics and mechanical properties of the regulating joints with the CrCoNi interlayer. Results demonstrate that the CrCoNi enhances the temperature at the steel-side interface through friction with 42CrMo steel and 6061-T6 aluminum, combined with adjustments in the friction sequence and duration, promoting plastic deformation. The axial transfer of heat creates a temperature gradient at the joint, enabling low-temperature welding on the aluminum side and forming a mechanical interlocking structure at the interface. The diffusion of Cr, Co, and Ni elements regulates the type and thickness of interfacial intermetallic compounds, ultimately enhancing the joint's strength. The thickness of the intermetallic compounds AlNi3, FeAl3, AlCo, and Fe2Al5 formed at the interface is less than 2 μm. A phase transformation occurred at the 42CrMo high-strength steel interface, leading to the formation of numerous needle-like martensites, which increased the Vickers hardness in the welding seam to 763.9 HV. The joint's tensile strength initially increased and then decreased with increasing friction speed, reaching a maximum of 168.7 MPa at 4000 rpm, which is more than 60% of the aluminum alloy base material's tensile strength.

Synergistic solid–liquid composite and rapid solidification preparation of aluminum-clad steel wires

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

Integrating interfacial bonding and coordinated deformation in steel/Al bilayers via a pin-less friction stir-assisted synchronous joining-forming approach

Interfacial microstructure and strengthening mechanism of stainless steel/carbon steel laminated composite fabricated by liquid-solid bonding and hot rolling

Effect Of Intermediate Annealing On The Interface And Plasticity Of Cu-Ni-Si/Al-Mg-Si Clad Composite Wires

Fabrication of a novel high-strength and high-conductivity copper-clad aluminum composite wire

Effect of the Addition of Steel Fibers on the Bonding Interface and Tensile Properties of Explosion-Welded 2A12 Aluminum Alloy and SS-304 Steel

Enhanced Interface Strength in Steel-Nickel Bimetallic Component Fabricated Using Wire Arc Additive Manufacturing with Interweaving Deposition Strategy

Interfacial Microstructure and Mechanical Properties of Al/steel Joints Fabricated Via Thermo-Compensated Resistance Brazing Welding with Cold Spray Zn Interlayer

Technological Parameters of Stainless Steel-Aluminum Alloy Semisolid Joining Clad

Microstructure and properties research of Al-Zn-Mg-Cu alloy with high strength and high elongation fabricated by wire arc additive manufacturing

Interface evolution and strengthening of two-step roll bonded cu/Al clad composites

Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects

Influence of the Surface State on the Interfacial Bonding Strength of the Cold-Rolled Brass/Carbon Steel Composite

Enhanced inertia friction welding of aluminum alloy and high-strength steel using CrCoNi interlayer: Microstructural and mechanical characterization

Improved interfacial strength in bimetallic additive manufacturing of aluminum bronze/steel by controlling interface melting

Research on the Microstructure and Properties of Al Alloy/Steel CMT Welding-Brazing Joints with Al–Si Flux-Cored Welding Wires

Synergistic-Strengthening Strategy Induce Excellent Electrical and Mechanical Properties in Cu/Alcrcufeni 2.5 Composites

Interfacial Bonding Behaviours of AA5052/DC05 in Synchronous Thermomechanical Joining-Forming Process

Achieving High-Quality Al/Steel Joint with Ultrastrong Interface

Novel approach to optimize the mechanical properties of Cu-Al composite wires