Abstract:Introduction. The practical significance of non-stoichiometric titanium carbides TiCх in various fields of technology and in medicine is expanding. In this regard, it is important to investigate both methods of obtaining titanium carbide powder and its properties in a wide range of stoichiometry. One of the effective ways to influence the physical and mechanical properties of powder systems is its mechanical treatment. Under shock-shear action, which is realized during processing in a ball mill, mechanical energy is transferred to the powder system, as a result of which it is ground, centers with increased activity on newly formed surfaces are formed; phase transformations, crystal lattice deformation, amorphization, formation of defects, etc. are possible. The aim of this work is to study the effect of low-energy mechanical treatment in a ball mill on the structure, phase composition and parameters of the fine crystal structure of non-stoichiometric titanium carbide powder obtained by reduction of titanium oxide with carbon and calcium. Materials and methods. Powder of titanium carbide TiC, obtained by calcium carbonization of titanium oxide was investigated. The powder was treated in a drum type ball mill. The structure of the powders before and after treatment was studied using the Philips SEM 515 scanning electron microscope. The specific surface area was determined by the BET method. The phase composition and parameters of the fine crystal structure of powder materials were investigated by X-ray analyzes. Results and discussion. It was established that an increase of the time of mechanical treatment in a ball mill of a non-stoichiometric titanium carbide powder TiC0.7 leads to an increase in the specific surface area of the powder from 0.6 to 3.4 m2 / g, and the average particle size calculated from it decreases from 2 μm to 360 nm. It is shown that in the process of treatment of the non-stoichiometric titanium carbide TiC0.7 powder, its structural phase state changes. Powder particles consist of two structural components with different atomic ratio of carbon to titanium: TiC0.65 and TiC0.48. Mechanical treatment of titanium carbide powder leads to a decrease in the microstresses of the TiCx crystal lattice and the size of coherently diffracting domains (CDD) from 55 to 30 nm for the TiC0.48 phase. For the TiC0.65 phase, with an increase in the duration of mechanical treatment, as well as for TiC0.48, the size of CDD decreases, and the level of microdistortions of the crystal lattice increases. This indicates that in the process of mechanical treatment, not only the grinding of powder particles occurs, but also an increase in its defects.

Parameter optimization of high energy ball milling process for TiO2 powder using the Taguchi method

Use of Taguchi method for high energy ball milling of CaCO3

Parameter Optimization of Ball Milling Process for Silica Sand Tailing

OPTIMIZATION OF MILLING PARAMETERS OF PLANETARY BALL MILL FOR SYNTHESIZING NANO PARTICLES

High-energy ball milling of Al2O3–TiO2 powders

Optimization of the high energy ball-milling: Modeling and parametric study

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Effect of Ball Milling Conditions on the Microstructure and Dehydrogenation Behavior of TiH2 Powder

Comparative Study on Improving the Ball Mill Process Parameters Influencing on the Synthesis of Ultrafine Silica Sand: A Taguchi Coupled Optimization Technique

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Achieving Both High Hydrogen Capacity and Low Decomposition Temperature of the Metastable AlH3 by Proper Ball Milling with TiB2

Milling parameter optimization for refinement of NiO/Al mixtures and synthesis of Ni/Al2O3 nanocomposites

Evolution of Morphology, Particle Size and Oxidation Resistance of Recycled Ti-6Al-4V Powders Prepared by Planetary Ball Milling

Effect of ball mill time and wet pre-milling on the fabrication of Ti powders by recycling Ti machining chips by planetary milling

Raman spectroscopy of ball-milled TiO2

Low energy mechanical treatment of non-stoichiometric titanium carbide powder

Refinement of TiB2 Powders with High-speed Planetary Mill and Its Effect on TiB2 Sinterability

Process Parameters Optimization of Silica Sand Nanoparticles Production Using Low Speed Ball Milling Method

High-temperature ball milling: An efficient method to fabricate Ti and its alloy powder for additive manufacturing

Effect of Ball Milling Parameters on Properties of Nano-Sized Tungsten Powder via Mechanochemical Processing

Optimization of machining parameters for turning operation of heat-treated Ti-6Al-3Mo-2Nb-2Sn-2Zr-1.5Cr alloy by Taguchi method