Abstract:The objective of this work was to assess and understand the effects of a parametric variation performed on a typical overlapping rim seal geometry. The datum geometry has been the focus of a detailed experimental investigation employing a large-scale linear cascade subjected to a range of the mass flow rates and swirl velocities of the leakage air. The parametric variations described in this paper were examined using validated computational fluid dynamics (CFD). As a part of the parametric studies, both the axial and the radial seal clearance between the rotor fin (angel wing) and stator platform were varied as well as the length of the overlap between stator and rotor platforms. In addition, the effects of forward and backward facing annulus steps were also investigated. It has been found that a backward-facing annulus step was detrimental for all conditions considered, while a forward-facing step offered improvements for smaller step heights and/or lower leakage fractions. Tightening of the seal clearances closer to the annulus line improved the sealing effectiveness but often at the expense of increased losses. On the other hand, increasing the overlap length led to improvements in the sealing effectiveness with very small effects on the overall losses. Moving the rim seal away from the blade-leading edges reduced the pressure asymmetry at the rim seal and increased the flow uniformity of the leakage air. However, this led to an increased cross-passage flow (more negative skew) and higher losses at all but lowest leakage fractions. The results presented in this paper highlight the fact that there may not be an optimum rim seal solution that would offer an improvement for the full range of leakage fractions and that, for different rim sealing flows, there may be a different optimum geometry. In addition, rotor disk movements in radial and axial directions at various off-design conditions should be considered as a part of the design process. Based on the presented results, it may be of a benefit to the turbine designer to consider rotor disk designs that would be more biased towards the upstream and outward disk movements, which would result in tightening of the seal clearances and avoidance of a backward-facing annulus step.

DYNAMICS OF ROCKET ENGINE TURBOPUMP TURBINE SEAL CLEARANCE CHANGES

Performance Analysis of the Cylinder Gas Film Seal between Dual-Rotor Reverse Shafts Considering Lubrication and Centrifugal Expansion Effects

Effect of two-phase flow lubrication on sealing performance of spiral groove mechanical seal under high speed and low temperature conditions

Influence of Tip Clearance on Unsteady Flow in Automobile Engine Pump

The Effects of a Parametric Variation of the Rim Seal Geometry on the Interaction Between Hub Leakage and Mainstream Flows in High Pressure Turbines

A Numerical Study on Mechanical Seal Dynamic Characteristics Within a Reactor Coolant Pump

Choice of gas temperature at the turbopump turbine inlet

Brush seal design and secondary air system modification of a heavy-duty gas turbine to improve the output power

Use of Pressure Measurements to Determine Effectiveness of Turbine Rim Seals

Dynamic Leakage Analysis of Noncontacting Finger Seals Based on Dynamic Model

Methodology for Counter Torque, Power Loss, and Frictional Heat for Brush Seals Under Eccentric Transients

Turbopump Parametric Modelling and Reliability Assessment for Reusable Rocket Engine Applications

Influence factors of clearance leakage flowrate and clearance hydraulic axial force of pump-turbine

A Review of Tip Clearance in Propeller, Pump and Turbine

Analysis of Tip Clearance Effect on the Transportation Characteristics of a Multiphase Rotodynamic Pump Based on the Non-Uniform Bubble Model

Influence of Thermodynamic Effects on Rotor-Stator Cavity Flow in Liquid Oxygen Turbopump

Influence of Tip Clearance on Cavitation Characteristics of an Inducer of Turbopump: CFD Study

Clearance flow patterns and pressure distribution of a pump-turbine: Measurement and simulation of a rotating disk flow

Numerical investigation on the influence of nonuniform tip clearance on rotor tip-clearance flow field structure

Flow Characteristics Analysis of a High-Head Prototype Pump-Turbine During Turbine Start-Up: Effects of the Clearance

Analysis of the impeller's tip clearance size on the operating characteristics of the underwater vehicle with a new high-speed water jet propulsion pump