Abstract:The objective of this work was to assess and understand the effects of a parametric variation performed on a typical overlapping rim seal geometry. The datum geometry has been the focus of a detailed experimental investigation employing a large-scale linear cascade subjected to a range of the mass flow rates and swirl velocities of the leakage air. The parametric variations described in this paper were examined using validated computational fluid dynamics (CFD). As a part of the parametric studies, both the axial and the radial seal clearance between the rotor fin (angel wing) and stator platform were varied as well as the length of the overlap between stator and rotor platforms. In addition, the effects of forward and backward facing annulus steps were also investigated. It has been found that a backward-facing annulus step was detrimental for all conditions considered, while a forward-facing step offered improvements for smaller step heights and/or lower leakage fractions. Tightening of the seal clearances closer to the annulus line improved the sealing effectiveness but often at the expense of increased losses. On the other hand, increasing the overlap length led to improvements in the sealing effectiveness with very small effects on the overall losses. Moving the rim seal away from the blade-leading edges reduced the pressure asymmetry at the rim seal and increased the flow uniformity of the leakage air. However, this led to an increased cross-passage flow (more negative skew) and higher losses at all but lowest leakage fractions. The results presented in this paper highlight the fact that there may not be an optimum rim seal solution that would offer an improvement for the full range of leakage fractions and that, for different rim sealing flows, there may be a different optimum geometry. In addition, rotor disk movements in radial and axial directions at various off-design conditions should be considered as a part of the design process. Based on the presented results, it may be of a benefit to the turbine designer to consider rotor disk designs that would be more biased towards the upstream and outward disk movements, which would result in tightening of the seal clearances and avoidance of a backward-facing annulus step.

Use of Pressure Measurements to Determine Effectiveness of Turbine Rim Seals

Performance Analysis of the Cylinder Gas Film Seal between Dual-Rotor Reverse Shafts Considering Lubrication and Centrifugal Expansion Effects

A Combined Experimental and Turbulence-Resolved Modelling Approach for Aeroengine Turbine Rim Seals

An Experimental Study of Turbine Vane Film Cooling Using Endoscope-Based PSP Technique in a Single-Passage Wind Tunnel

A theoretical model for ingress through turbine rim seals based on physically-observed unsteadiness

Numerical Investigations of Flow Structures in Radial Rim Seal and a Modification of the Orifice Model

Numerical Investigation for Ingestion Characteristics of 1.5-Stage Turbine Rim Seal

Numerical Investigations On The Sealing Effectiveness Of Turbine Groove Radial Rim Seal

Numerical Investigation on the Steady and Unsteady Flow Characteristics of Rim Seal for the First Stage in Gas Turbine

Unsteady Numerical Investigation on the Sealing Effectiveness and Flow Field in Different Rim Seal Geometries

Effect of Outer Fin Axial Gap on the Sealing Effectiveness and Fluid Dynamics of Radial Rim Seal

Numerical Investigations on the Sealing Performance and Ingestion Mechanism of Rim Seals for a 1+1/2 Counter-Rotating Turbine

Effects of Aerodynamic and Operational Parameters on Sealing Performance of Turbine Rim Seal

The Effects of a Parametric Variation of the Rim Seal Geometry on the Interaction Between Hub Leakage and Mainstream Flows in High Pressure Turbines

Investigations on the Sealing Effectiveness and Unsteady Flow Field of 1.5-Stage Turbine Rim Seal

Numerical Investigations on the Sealing Effectiveness of Turbine Honeycomb Radial Rim Seal

Numerical Investigation on the Steady and Unsteady Flow Characteristics of Rim Seal in Gas Turbine

Numerical investigation on the sealing efficiency of the turbine rim seal

Effect of Rim Seal Geometry On Rotationally-Driven Ingestion

Numerical Investigations on Gas Ingestion Mechanism Based on Flow Instabilities in Rim Seal and Cooling Characteristics of Endwall in a 1.5-Stage Axial Turbine

Effects of Rim Seal Geometries on Aerodynamic Performance and Rotor Platform Cooling in a One-Stage Turbine