Abstract:The gas turbine has an assembly gap between the combustion chamber and the first stage vane. The coolant air discharge from the gap can prevent the ingestion of the high temperature gas. This leakage flow also provides a cooling coverage on the vane endwall. Taking the cooling effect of the leakage flow on the endwall into consideration is very important for an efficient cooling design. In this paper, the cooling effect of leakage flow on endwall is studied by means of experimental and numerical methods. The study included slots at 30°, 45°, and 60° angles, and six blowing ratios of 0.3, 0.6, 1.0, 1.4, 1.7, and 2.0. The experiment and numerical calculation are conducted under the condition that the inlet Mach number is 0.125 and the outlet Mach number is 0.72, which is close to the working Mach number of the real gas turbine. Under the same slot inclination and blowing ratio, the distribution of endwall adiabatic cooling effectiveness is more nonuniform under the condition of near-real engine Mach number. This is because the passage vortex is weaker under the low Mach number condition, and the leakage flow has a better wall attachment effect. In terms of the spanwise average of endwall adiabatic cooling effectiveness, when the blowing ratio is small, the adiabatic cooling effectiveness is lower under the condition of near-real engine Mach number than that under the condition of low Mach number, but the opposite is true under the condition of large blowing ratio. This is because under the condition of large blowing ratio, the turbulence is stronger under the condition of Mach number of near-real engine. With the reduction of blowing ratio, the turbulent kinetic energy weakens more strongly. In the studied cases, there is a critical blowing ratio of 1.0, and the total endwall cooling adiabatic cooling effectiveness is not significantly affected by the Mach number when it is smaller than M1.0. The average adiabatic cooling effectiveness of the endwall under the condition of near-real engine Mach number is about 7% lower than that under the condition of low Mach number. It means that the experimental results of leakage flow cooling obtained under the condition of low inlet Mach number need to be corrected by a correction factor, which may be less than 1 to make it engine relevant.

Effects of Rim Seal Exit Geometry on the Cooling Characteristics of Turbine Endwall and Blade Suction Side

Experimental and Numerical Investigations into the Effects of Rim Seal Structure on Endwall Film Cooling and Flow Field Characteristics

An Experimental Study of Turbine Vane Film Cooling Using Endoscope-Based PSP Technique in a Single-Passage Wind Tunnel

Unsteady Numerical Investigation on the Sealing Effectiveness and Flow Field in Different Rim Seal Geometries

Effect of Inlet Mach Number on Aerothermodynamics of Sealing Leakage Flow Cooling on Endwall

Effect of Leakage Flow on the Endwall Cooling Performance in High Subsonic Turbine Cascade

Numerical investigation on the effect of sealing clearance on endwall film cooling effectiveness under rotating condition

Numerical investigation of the purge flow mechanisms and heat-transfer characteristics of turbine rim seals

The Film Cooling Effect of Leakage From Midpassage Gap on Downstream Endwall

Contoured Endwall Flow And Heat Transfer Experiments With Combustor Coolant And Gap Leakage Flows For A Turbine Nozzle Guide Vane

Experimental and Numerical Investigation on Middle Passage Gap Leakage with Different Mass Flow Rate and Injection Angle on Turbine Endwall

Cooling Effectiveness and Aerodynamic Performance in a 2D-Contoured Endwall Passage with Different Mass Flow Ratios

Parameter sensitivity analysis of the interaction between purge flow and mainstream

Numerical Investigation on the Effect of Hot Running Rim Seal Clearance on Hot Gas Ingestion into Rotor-Stator System

Effects of mid-passage gap with a variable surface angle on a turbine vane endwall’s aerothermal and film cooling performances

Effects of Endwall Misalignment on Endwall Purge Flow Film Cooling

Turbine Endwall Film Cooling with Combustor-Turbine Interface Gap Leakage Flow: Effect of Incidence Angle

Effect of non-axisymmetric endwall contouring and swirling inlet flow on film cooling performance of turbine endwall

The Effects of a Parametric Variation of the Rim Seal Geometry on the Interaction Between Hub Leakage and Mainstream Flows in High Pressure Turbines

Experimental and Numerical Investigations of Discrete Film Holes Cooling Performance on a Blade Endwall with Mid-Passage Gap Leakage

Experimental Investigation of Turbine Phantom Cooling on Suction Side with Combustor-Turbine Leakage Gap Flow and Endwall Film Cooling