Abstract:The transient process of a centrifugal pump existed in a variety of occasions. There were a lot of researches in the external characteristic in startup process and stopping process, but internal characteristics were less observed and studied. Study of the internal flow field had significant meanings. The performance of a pump could be evaluated and improved by revealing the flow field. In the other hand, the prediction of external characteristic was based on the correct analysis of the internal flow. In this paper, theoretical method and numerical simulation were used to study the internal characteristic of a centrifugal pump. The theoretical study showed that the relative flow in an impeller was composed of homogeneous flow and axial vortex flow. The vortex intensity was mainly determined by angular velocity of impeller, flow channel width and blade curvature. In order to get the internal flow field and observe the evolution of transient internal flow in the impeller, Computational Fluid Dynamics(CFD) were used to study the three-dimensional unsteady incompressible viscous flows in a centrifugal pump during starting period. The Dynamic Mesh (DM) method with non-conformal grid boundaries was applied to get the external characteristic and internal flow field. The simulate model included three pumps with different blade numbers and the same blade curvature. The relative velocity vector showed that there was a big axial vortex in impeller channel. At the beginning, the vortex was raised in the pressure side of the impeller outlet and with time went on, it shifted to the middle flow channel of the impeller and the vortex intensity increased. When the speed and flow rate reached a definite value, the influence of the axial vortex began to get smaller. The vortex developed faster when the flow channel got narrower. Due to the evolution of axial vortex, the slip factor during starting period was smaller than that in quasi-steady condition. As a result, transient head was lower than quasi-steady head in startup process.

Flow Characteristics Analysis of a High-Head Prototype Pump-Turbine During Turbine Start-Up: Effects of the Clearance

Influence of End Wall Clearance on Guide Vane Self-Excited Vibrations at Small Openings during Pump Mode’s Starting Up Process of a Reversible Pump Turbine

Influence factors of clearance leakage flowrate and clearance hydraulic axial force of pump-turbine

Clearance flow patterns and pressure distribution of a pump-turbine: Measurement and simulation of a rotating disk flow

Numerical Investigation of Flow and Structural Characteristics of a Large High-Head Prototype Pump–Turbine during Turbine Start-Up

Influence of Clearance Flow on Dynamic Hydraulic Forces of Pump-Turbine during Runaway Transient Process

Numerical Study on the Effect of Crown Clearance Thickness on High-Head Pump Turbines

Flow-induced Vibration Analysis of a Prototype Pump-Turbine Runner During Turbine Start-Stop Transient Process

Influence of Runner Clearance on Efficiency and Cavitation in Kaplan Turbine

Transient Internal Characteristic Study of a Centrifugal Pump During Startup Process

Analysis of clearance flow of a fuel pump based on dynamical mode decomposition

Clearance Flow Field Characteristics of Kaplan Turbine under Different Flange Clearance

Flow-Induced Vibration of Non-Rotating Structures of a High-Head Pump-Turbine during Start-Up in Turbine Mode

Analysis of Internal Flow Characteristics of a Startup Pump Turbine at the Lowest Head under No-Load Conditions

Three-dimensional simulation of unsteady flows in a pump-turbine during start-up transient up to speed no-load condition in generating mode

Head-Cover Vibration Investigation of a Prototype Reversible Pump-Turbine Unit During Start-up in Pump Mode. Part I: Fluid Dynamic Analysis

Effect of Tip Clearance on Helico-Axial Flow Pump Performance at Off-Design Case

Investigations into Hydraulic Instability during the Start-Up Process of a Pump-Turbine under Low-Head Conditions

Transient Flow Dynamics Analysis of a Large Prototype Francis Turbine at Different Loads

Analysis of Flow Characteristics in Pumped Storage Unit During Start-Up in Turbine Mode

Investigation of the Starting-Up Axial Hydraulic Force and Structure Characteristics of Pump Turbine in Pump Mode