Abstract:The preparation and tribological properties of PAI/PI‐EPN polymer coatings. To improve the tribological properties of polar crane copper alloy bearings to withstand wear under dry sliding wear and grease lubrication at low temperatures, three kinds of coating materials modified by incorporating WS2 and SiC into polyamide‐imide/polyimide‐phenolic epoxy resin were designed. These composite coatings were sprayed on the surfaces of CuPb22.5Sn2.5 copper alloys by liquid spraying technique. Firstly, the tribological experiments were performed with three different coatings. Then, nanoindentation testing and wear morphology analysis were conducted. The results show that the hardness of the composite coatings decreases with the increase of WS2. As the content of WS2 increases, the coefficients of friction (CoFs) of coatings decreases under dry sliding wear. The S2 coating filled with 7.5 wt% WS2 exhibits the lowest wear rate and the best wear resistance under low temperature and dry sliding wear. The coatings form a lubricating film on the worn surface under dry sliding wear at −70°C, improving the wear resistance of the coatings. The primary wear mechanisms are adhesive wear and fatigue wear. The wear rates of the coatings increase with the increasing content of WS2 under low‐temperature grease lubrication. The S1 coating filled with 5.0 wt% WS2 exhibits the lowest wear. The S1 coating demonstrates a CoF of 0.07 and a wear rate of 6.5 × 10−6 mm3N−1 m−1 at 0°C, showing excellent friction‐reducing and wear‐resistant properties. The primary wear mechanism is adhesive wear. The wear mechanisms of polymer coatings are closely related to temperature. The dominant wear mechanisms transfer from abrasive wear to adhesive wear and fatigue wear under dry sliding wear and decreasing temperature. The wear mechanisms transfer from predominantly adhesive and abrasive wear to adhesive wear, fatigue wear, and abrasive wear under grease lubrication. The hardness of the coatings and the behavior of the polymer at various low temperatures are the primary factors that affect the differing wear mechanisms.

Tribological Behavior of Cu-Modified Polymer-derived SiBCN Ceramics at Elevated Temperature

High temperature tribological behavior of polymer-derived Ta4HfC5 nanoceramics

Tribological Behavior of Liquid Phase Sintered SiC Ceramics Under Dry Condition

Self-lubricating behavior caused by tribo-oxidation of Ti3SiC2/Cu composites in a wide temperature range

Polymer derived SiBCN(O) ceramics with tunable element content

Tribological Behavior of Ti3SiC2 and Ti3SiC2/Pb Composites Sliding Against Ni-based Alloys at Elevated Temperatures

Synthesis and Tribological Characterization of Ti3SiC2/ZnO Composites

High temperature tribological behaviors and wear mechanisms of NiAl-MoO3/CuO composite coatings

Tribological Behavior and Wear Mechanism of Cu-SiO2 Sintered Composite under Different Sliding Speeds

The investigation of tribological properties of PAI/PI‐EPN polymer coating filled with WS2 and SiC at low temperatures

Tribological properties of h-BN matrix solid-lubricating composites under elevated temperatures

Tribological behavior and mechanism of h-BN modified copper metal matrix composites paired with C/C–SiC

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Mechanical and tribological properties of h-BN/ZrO2/SiC solid-lubricating ceramic composites

The Tribological Properties and Wear Mechanism of Copper Coated Graphite Doped Sialon Ceramic Composites at Wide Range Temperature from 25 to 800 °C

Dry sliding tribological properties of Cu-WS 2 self-lubricating composites at 25–500 °C

High-temperature Tribological Properties of Si3N4/TiC Ceramic with Bionic Surface Textures and DLC Coatings

Friction and wear performance of CrSiBCN coatings sliding against ceramic and metal counterparts in sea water

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

The Tribological and Adsorption Performance of Chlorophenyl Silicone Oil Using Different Ceramic Materials under High Temperature

Tribological behavior of h -BN/Al 2 O 3 self-lubricating composites in extreme environments–Part I: Lubricating behavior and ultra-low friction coefficient mechanism in air environments from room temperature to 1200 °C