Abstract:Electrochemical reduction of carbon dioxide via CO2 co-electrolysis (CO2ELY) is an essential process to produce non-fossil chemical feedstock acting as CO2 sink. The required electrical energy can be harvested from temporal surplus of renewable energy sources like solar or wind. Employing a bipolar electrolyte membrane (BPM) in forward-bias is a promising approach to mitigate fundamental problems of the current technological fore-runner design that employs an anion exchange membrane (AEM). We employed synchrotron time-resolved X-ray tomographic microscopy (XTM) to study degradation processes in BPM CO2ELY. In forward-bias BPM co-electrolysis, the cation exchange layer (CEL) faces the anode to provide favorable acidic conditions for the oxygen evolution reaction. Such acidic anode allows using pure water as electrolyte eliminating the salt precipitation at the cathode observed for AEM CO2ELY. As the second major issue in AEM CO2ELY, (bi)carbonate ions formed at the cathode are transported to the anode presenting a major obstacle for high CO2 conversion efficiency. The then required effort to separate CO2 from the electrolyte further reduces the overall energy efficiency. Employing a BPM and introducing the CEL prevents (bi)carbonate ions reaching the anode. BPM CO2ELY retains at the same time the advantages of AEM CO2ELY of performing CO2 reduction under alkaline conditions with the anion exchange layer (AEL) of the BPM facing the cathode. However, BPM CO2ELY suffers from low current density and poor stability in the range of only a few hours. Current limiting factors and degradation processes as well as the affected components are rarely investigated and poorly understood. Processes that have been brought forward are cathode flooding similar to fuel cells or catalyst poisoning. We employ synchrotron XTM to investigate structural dynamics in CO2ELY during operation. The brilliant synchrotron source allows us to acquire one full high-quality scan with a voxel size of 2.75 um in 1 s. We acquired one scan every minute for one hour during electrochemical operation. The image data reveals the formation of gas bubbles at the AEL-CEL junction and ultimately delamination of the BPM. We explain the gas formation as the recombination of (bi)carbonate ions with hydrogen ions at the junction producing gaseous CO2. This CO2 additionally reaches the anode by diffusion causing partial delamination of the anode catalyst layer. CO2 escaping from the AEL surface at the anode forms high-pressure gas bubbles that break the water wet catalyst layer. A diffusive model considering the transport of ions and neutral CO2 is able to capture the mechanism. Our imaging experiments provide insights not attainable by other diagnostic methods and highlight the need for fundamental research on forward-bias BPM CO2ELY. Knowledge based on AEM CO2ELY and fuel cells is not necessarily directly applicable and specific studies on BPM CO2ELY are required to increase performance and stability. We gratefully acknowledge provision of beamtime at TOMCAT, SLS, Paul Scherrer Insititut, Villigen PSI, Switzerland. Figure 1: Tomographic slice of CO2-electrolyser (cathode to the left) a) before operation and running water through anode b) after 23 minutes operation at 3.5V constant potential showing liquid water dynamics at cathode, membrane swelling, gas formation within the membrane and anode catalyst layer disintegration. Figure 1

ICP–MS Assisted EDX Tomography: A Robust Method for Studying Electrolyte Penetration Phenomena in Gas Diffusion Electrodes Applied to CO2 Electrolysis

Cracks as Efficient Tools to Mitigate Flooding in Gas Diffusion Electrodes Used for the Electrochemical Reduction of Carbon Dioxide

Spatio‐Temporal Electrowetting and Reaction Monitoring in Microfluidic Gas Diffusion Electrode Elucidates Mass Transport Limitations

Scanning Gas Diffusion Electrode Setup for Real-Time Analysis of Catalyst Layers

Quantifying mass transport limitations in a microfluidic CO 2 electrolyzer with a gas diffusion cathode

Hierarchically Conductive Electrodes Unlock Stable and Scalable CO2 Electrolysis

Near-Electrode Concentration Gradients of Bicarbonate and pH within Porous Gas Diffusion Electrode for Optimized Selective CO2 Electroreduction to C2+ Products

Real Time Analysis of the CO2 Reduction Reaction Products in a Cu-Gde Setup

Probing the Catalytically Active Region in a Nanoporous Gold Gas Diffusion Electrode for Highly Selective Carbon Dioxide Reduction

Near-Electrode Concentration Gradients of Bicarbonate and pH within Porous Gas Diffusion Electrode for Optimized Selective CO 2 Electroreduction to C 2+ Products

Design and Application of a Gas Diffusion Electrode (GDE) Cell for Operando and In Situ Studies

Best Practices and Common Pitfalls in Experimental Investigation of Electrochemical CO 2 Reduction at Gas Diffusion Electrodes

Gas Diffusion Electrodes (GDEs) for Carbon Dioxide (CO 2 ) Reduction in Microfluidic Cells: Towards a Fluid Dynamics Assisted Rational Design

Pore accessibility matters in CO 2 electrolysis: Preventing H 2 formation and boosting triple-phase boundary on microtubular gas-diffusion electrodes

Gas diffusion electrodes, reactor designs and key metrics of low-temperature CO2 electrolysers

Gas diffusion enhanced electrode with ultrathin superhydrophobic macropore structure for acidic CO 2 electroreduction

Scale-Up of PTFE-Based Gas Diffusion Electrodes Using an Electrolyte-Integrated Polymer-Coated Current Collector Approach

Hydrophobized electrospun nanofibers of hierarchical porosity as the integral gas diffusion electrode for full-pH CO2 electroreduction in membrane electrode assemblies

An optimised cell for in situ XAS of gas diffusion electrocatalyst electrodes

Degradation Processes in Bipolar Membrane CO2-Electrolysis Studied by Time-Resolved X-Ray Tomography

Scalable Gas Diffusion Electrode Fabrication for Electrochemical CO2 Reduction Using Physical Vapor Deposition Methods.