Abstract:Abstract A real industrial electroplating rinsing wastewater was collected and subjected to physical and chemical examination. The study showed that it can be categorized as high strength wastewater, at pH- 2, COD 1430 mg/l, and high level of metals above permissible limits, namely: 150, 30, 25, and 2.9 for Ni, Cu, Zn, and Fe mg/l respectively. Therefore, metals must be adequately removed before discharging to avoid any hazardous impact on the environment. Similar synthetic wastewater was prepared to study the effect of chemical coagulation for the precipitation of metals. The optimum removal rate was achieved by using a combination of lime and ferric chloride at 100 and 30 mg/l respectively. The chemically treated electroplating wastewater was subjected to an electrocoagulation study. A comparison between iron and stainless-steel electrodes for the removal of metals was investigated. Furthermore, the effect of different electric voltages, and contact time on metals removal efficiency were also examined. It was found that the optimum removal capacity was achieved when a stainless steel electrode was employed in the presence of ferric chloride as coagulant, at 10 volts, 30 min. contact time, and pH 9 for synthetic solution. In a batch treatment system, the real industrial wastewater was treated at the predetermined optimum operating conditions; the removal of metals was 92.1%, 87.8% and 82.9% for Ni. Zn, and Cu respectively. By employing a continuous flow reactor for the treatment of the same real wastewater and under the same operating conditions, metals removal rate increased to 98.9%, 97.4% and 96.6% for Ni. Zn, and Cu respectively. The level of metals in the final treated wastewater copes with Egyptian Environmental Regulation. The overall results confirmed that the electro-coagulation (EC) technology offers an effective alternative process in combination with the conventional chemical coagulation process for reaching high removal performance of toxic metals from the electroplating wastewater. The advantage of EC technique is achieving high treatment efficiency instead of expensive chemical reagents, high construction cost and/or other conventional processes. In addition, the final treated water can be reused for rinsing process in the electroplating industry and/or discharging without any environmental hazard effect. It is also recommended to employ solar energy instead of electricity to reduce cost of operation.

Nickel (II) removal from real electroplating wastewater in an electrocoagulation reactor: parametric optimization by response surface methodology

A Comparative Study Of Nickel(Ii) Removal From Electroplating Wastewater By Pre-Precipitation Combined With Fenton-Precipitation Or Fenton-Like-Precipitation

Nickel removal from wastewater using electrocoagulation process with zinc electrodes under various operating conditions: performance investigation, mechanism exploration, and cost analysis

Electrochemical reactor with rotating cylinder electrode for optimum electrochemical recovery of nickel from plating rinsing effluents

Removal of Ni(II) ions from wastewater by ion exchange resin: Process optimization using response surface methodology and ensemble machine learning techniques

Removal of low concentrations of nickel ions in electroplating wastewater by combination of electrodialysis and electrodeposition

Highly efficient nickel recovery from industrial wastewater via synergistic electrodeposition and electrocatalytic oxidation technique

Copper, chromium and nickel removal from metal plating wastewater by electrocoagulation

Electrocoagulation removal of Pb, Cd, and Cu ions from wastewater using a new configuration of electrodes

Removal of nickel through sulfide precipitation and characterization of electroplating wastewater sludge

Development of electrocoagulation process for wastewater treatment: optimization by response surface methodology

Treatment of industrial electroplating wastewater for metals removal via electrocoagulation continous flow reactors

Enhanced chromium removal from tannery wastewater through electrocoagulation with iron electrodes: Leveraging the Box-Behnken design for optimization

Intensification of a new electrocoagulation system characterized by minimum energy consumption and maximum removal efficiency of heavy metals from simulated wastewater

Recovery of nickel from electroless nickel plating wastewater based on the synergy of electrocatalytic oxidation and electrodeposition technology

Treatment of CNC industry wastewater by electrocoagulation technology: an application through response surface methodology

Pollutants removals and energy consumption in electrochemical cell for pulping processes wastewater treatment: Artificial neural network, response surface methodology and kinetic studies

Recovery of Nickel by Electrolytic Method from Electroplating Wastewater

Selective recovery of Nickel from electroplating rinse bath wastewater by an integrated Donnan Dialysis/precipitation process

A hybrid system for Nickel ions removal from synthesized wastewater using adsorption assisted with electrocoagulation

Removal of Low-Concentration Nickel in Electroplating Wastewater Via Incomplete Decomplexation by Ozonation and Subsequent Resin Adsorption