Abstract:Structure of nano amorphous matter has not been studied sufficiently yet due to the difficulty in both operation of nano matter and characterization of their structure. In this work, a detailed study of the structural orientation within amorphous polymeric nanofiber and its mechanical strength was conducted for a highly thermal resistant amorphous polymer: poly(phthalazinone ether ketone) (PPEK). Poly(butylene terephthalate) (PBT), a semi-crystalline polymer with partial difference in chain flexibility and geometry to PPEK, was chosen for a comparative discussion. For the method, highly aligned PPEK and PBT nanofiber bundles were prepared by electrospinning with a home-made book-like collecting device. X-ray experiments were conducted to research their structural orientation, and tension experiments were conducted to research their mechanical properties. It was found that the amorphous PPEK nanofibers showed relatively low orientation degree of polymer chain limited by its rigid and twisted segments within the polymer chain, while PBT nanofibers showed not only highly ordered crystal structure but also very large shish length, beneficial from the co-existence of rigid and flexible segments. The above structural information was well supported by their uniaxial tensile behaviors, where PBT nanofiber manifested much larger ultimate stress σ, failure strain ε, Young’s modulus E and toughness than those of PPEK nanofibers and commercial PBT plastic. However, the electrospun PBT nanofibers’ orientation degree, within the range of 0.45–0.7, is much lower than that of some reported melt-spun PBT fibers with the orientation degree above 0.9. Therefore, it can be concluded that the instinct characterization of polymer chain and processing technique have a much more significant influence than size effect on the structural orientation and mechanical strength of nanofibers rather than size effect.

Thermal Conductivity of Individual Electrospun Polymer Nanofibers

Thermal Conductivity of Electrospinning Chain-Aligned Polyethylene Oxide (PEO)

A Rapid and Simple Method to Draw Polyethylene Nanofibers with Enhanced Thermal Conductivity

Thermal Conductivity of High-Modulus Polymer Fibers

Structure-induced enhancement of thermal conductivities in electrospun polymer nanofibers.

Thermal Conductivity in the Radial Direction of Deformed Polymer Fibers.

High Thermal Conductivity of Polyethylene Nanowire Arrays Fabricated by an Improved Nanoporous Template Wetting Technique

Experimental Study of Thermal Conductivity of Polyethylene Nanowire Arrays Fabricated by the Nanoporous Template Wetting Technique

Thermal Transport in Electrospun Vinyl Polymer Nanofibers: Effects of Molecular Weight and Side Groups.

Preparation and Properties of Electrospun GO/PEO Nanofibers

Novel Polyethylene Fibers of Very High Thermal Conductivity Enabled by Amorphous Restructuring.

Investigation of Dielectric Strength of Electrospun Nanofiber Based Thermal Interface Material

Research on Thermal Conductivity of Electrospun Polyacrilonitrile-Multi-Walled Carbon Nanotubes Composite Carbon Nanofiber Papers.

Coaxial Electrospinning Of Polyurethane(Shell)/Nylon-6(Core) For Textile Applications

Comparative Analysis of Thermal Characteristics: Virgin Polyacrylonitrile (PAN) Versus Electrospun Pan Nanofibre Mats

Thermal Properties Of Carbon Nanofiber Reinforced High-Density Polyethylene Nanocomposites

Study of the structural orientation and mechanical strength of the electrospun nanofibers from polymers with different chain rigidity and geometry

Investigation Of The Thermo-Mechanical Property Of Knitting 3d Polyethylene: A Comparative Study

Influence of Collecting Velocity on Fiber Orientation, Morphology and Tensile Properties of Electrospun PPESK Fabrics

The effects of electrospinning parameters on coaxial polyacrylonitrile/polyurethane nanofibers: Morphology and water vapour transmission rate

Effect of Fiber Diameter on Thermal Conductivity of the Electrospun Carbon Nanofiber Mats