Abstract:To address the issue that a single coating agent cannot simultaneously enhance Li+-ion transport and electronic conductivity of Ni-rich cathode materials with surface modification, in the present study, we first successfully synthesized a LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material by a Taylor-flow reactor followed by surface coating with Li-BTJ and dispersion of vapor-grown carbon fibers treated with polydopamine (PDA-VGCF) filler in the composite slurry. The Li-BTJ hybrid oligomer coating can suppress side reactions and enhance ionic conductivity, and the PDA-VGCFs filler can increase electronic conductivity. As a result of the synergistic effect of the dual conducting agents, the cells based on the modified NCM811 electrodes deliver superior cycling stability and rate capability, as compared to the bare NCM811 electrode. The CR2032 coin-type cells with the NCM811@Li-BTJ + PDA-VGCF electrode retain a discharge specific capacity of ∼92.2% at 1C after 200 cycles between 2.8 and 4.3 V (vs Li/Li+), while bare NCM811 retains only 84.0%. Moreover, the NCM811@Li-BTJ + PDA-VGCF electrode-based cells reduced the total heat (Qt) by ca. 7.0% at 35 °C over the bare electrode. Remarkably, the Li-BTJ hybrid oligomer coating on the surface of the NCM811 active particles acts as an artificial cathode electrolyte interphase (ACEI) layer, mitigating irreversible surface phase transformation of the layered NCM811 cathode and facilitating Li+ ion transport. Meanwhile, the fiber-shaped PDA-VGCF filler significantly reduced microcrack propagation during cycling and promoted the electronic conductance of the NCM811-based electrode. Generally, enlightened with the current experimental findings, the concerted ion and electron conductive agents significantly enhanced the Ni-rich cathode-based cell performance, which is a promising strategy to apply to other Ni-rich cathode materials for lithium-ion batteries.

Improving Fast Charging-Discharging Performances of Ni-Rich LiNi0.8Co0.1Mn0.1O2 Cathode Material by Electronic Conductor LaNiO3 Crystallites

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Ionic Conductive Interface Boosting High Performance LiNi0.8Co0.1Mn0.1O2 for Lithium Ion Batteries

Surface Coating of NCM-811 Cathode Materials with G-C3n4 for Enhanced Electrochemical Performance.

Enhanced electrochemical performance of cobalt oxide layers coated LiNi0.8Co0.1Mn0.1O2 by polyvinylpyrrolidone-assisted method cathode for Li-ion batteries

Mixed-conducting Interlayer Boosting the Electrochemical Performance of Ni-rich Layered Oxide Cathode Materials for Lithium Ion Batteries

Concerted Effect of Ion- and Electron-Conductive Additives on the Electrochemical and Thermal Performances of the LiNi0.8Co0.1Mn0.1O2 Cathode Material Synthesized by a Taylor-Flow Reactor for Lithium-Ion Batteries

In situ epitaxial growth and electrochemical conversion of LiNi0.5Mn1.5O4 thin layer on Ni-rich cathode materials for high voltage lithium-ion batteries

Enhanced cyclic stability and discharge capacity of NCM811 cathode by coating ferroelectric-type LiNbO 3 ionically conductive layer

Stabilization of NCM811 cathode for Li-ion batteries by N-doped carbon coating

Long-cycle Lithium batteries with LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathodes above 4.5 V enabled by uniform coating of nanosized garnet electrolytes

Enhanced electrochemical performance of LiV2O4-coated and V4+-doped LiNi0.8Co0.1Mn0.1O2 cathode for lithium-ion batteries

Boosting the performance of LiNi0.90Co0.06Mn0.04O2 electrode by uniform Li3PO4 coating via atomic layer deposition

Enhanced Electrochemical Performance of Perovskite LaNiO3 Coating on Li1.2Mn0.54Ni0.13Co0.13O2 As Cathode Materials for Li-ion Batteries

Enhanced rate performance and mitigated capacity decay of single-crystal LiNi0.8Co0.1Mn0.1O2 by the synergism of Mg doping and V2O5 coating

Double Conductor Coating to Improve the Structural Stability and Electrochemical Performance of LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode Material

Optimized structure stability and cycling performance of LiNi0.8Co0.1Mn0.1O2 through homogeneous nano-thickness Al2O3 coating

Enhanced electrochemical performance of Ni-rich cathode material by N-doped LiAlO2 surface modification for lithium-ion batteries

An Efficient Synthetic Method To Prepare High-Performance Ni-Rich Lini0.8co0.1mn0.1o2 For Lithium-Ion Batteries

High structure stability and Li-conduction of LiNi0.8Co0.1Mn0.1O2 cathode co-coated by Al2O3 and LiNbO3 for high performance lithium-ion battery