Abstract:Purpose This paper aims to examine the precision loss of ball screw raceway under different operating conditions and geometry parameters. Design/methodology/approach Based on a new coefficient K’ introduced especially for ball screws to reflect the actual contact condition, the modified Archard theory is applied to ball screws to obtain wear volume of the ball-screw contacts. Thus, the axial precision loss can be defined as the ratio of the wear volume to the contact area. Meanwhile, a novel running bench and a precision-measuring system of ball screws are conducted. Precision variation is obtained and analyzed during the whole life running test, which agrees well with the theoretical values calculated in this paper. Findings For a given rotational speed, the increasing rate of the precision loss rate is high at low axial load and then becomes small with the increasing axial load, whereas for a given axial load, the precision loss rate is proportional to the rotational speed. Besides, the precision loss rate is reduced with the increasing contact angle between a ball and the screw raceway, and is proportional to the helix angle when the angle changes from 1 to 10 degrees. Research limitations/implications The rotational speed used in this experiment is low and the ball screw is of no-load type, although results calculated by the model and Wei’s model seem close when the axial load is high, whether the model built in the paper is applicable to the condition of high rotational speed and preload still needs to be verified in the future work. Practical implications This study provides an accurate model to predict the precision loss of the screw raceway and estimate the remaining life of ball screws, which is significant for better performance of ball screws as well as the computer numerical control machine tools. Originality/value Previous studies on the wear of ball screws mainly focused on the drag torque analysis and mechanical efficiency estimation, and the experiment to verify their theoretical analysis was almost all limited to the test of drag torque or axial rigidity, which is neither sufficient nor persuasive. However, in this paper, the authors proposed a comprehensive wear prediction model which combines the modified Archard wear theory, Hertz contact theory and kinematic theory of ball screws. To the best of the authors’ knowledge, this kind of study has never been reported in the literature. In addition, for the lack of the test bench and high cost of the experiment, the whole life operation test, which is designed and conducted to confirm the model in this paper, has never been reported in literature either.

Degradation reliability modeling for ball screws subject to fatigue elastic failure mode

A new two-stage degradation model for the preload of ball screws considering geometric errors

Fatigue life and fatigue reliability mechanism of ball bearings

The influence of different load distribution considering geometric error on the fatigue life of ball screw

Multivariate Accelerated Degradation Modeling and Reliability Assessment for Ball Screw Grease Based on Fractional Brownian Motion Process Model

Dynamic reliability analysis of mechanical components based on equivalent strength degradation paths

Methodology For Ball Screw Component Health Assessment And Failure Analysis

Research on Rolling Contact Fatigue Failure of the Bearing Used in High-Speed Electric Multiple Units’ Axle Box Based on a Damage-Coupled Elastic–Plastic Constitutive Model

Fatigue life and influencing factors of a mechanical elastic wheel

Fatigue life analysis of spinning bearings for roller-guided bushing special machines considering creep-slip characteristic

Investigation of the precision loss for ball screw raceway based on the modified Archard theory

Dynamic modeling, analysis, and experimental study of ball screw pairs with nut spalling faults in electromechanical actuators

Comparison of Fatigue Reliability Life of Telescopic Rod of an Eccentric Telescopic Rod Conveyor with and without Strength Degradation

Time-variant reliability analysis of angular contact ball bearing considering the coupled effect of rolling contact fatigue damage and wear

Modeling and Fatigue Characteristic Analysis of the Gear Flexspline of a Harmonic Reducer

Research on fatigue reliability prediction model and structural improvement of welded drive axle housing based on master S‐N Curve method

Surface roughness prediction in ball screw whirlwind milling considering elastic-plastic deformation caused by cutting force: Modelling and verification

A Wear Prediction Framework for Ball-Screw of Electro-Mechanical Brake Unit on Railway Trains

Reliability modeling of gear system considering strength degradation

Low Order Static Load Distribution Model for Ball Screw Mechanisms Including Effects of Lateral Deformation and Geometric Errors

Static load distribution and axial static contact stiffness of a preloaded double-nut ball screw considering geometric errors