Simplified PMT Model

Karim Zbiri

DOI: https://doi.org/10.48550/arXiv.0809.4210

2008-09-24

Abstract:A simplified model is proposed based on the characteristics of the photomultiplier tube (PMT). The Model is compared to the available data, and it successes to reproduce the saturation profile of the PMT. The model also adds clarification about how the PMT works.

Instrumentation and Detectors

What problem does this paper attempt to address?

The Photon Detection Mode of Photomultiplier Tubes Considering the Pulse Height Distribution

Xiang Yu-Yan,Ma Yue,Guo Gao-Feng,Jing Quan,Li Song

DOI: https://doi.org/10.11972/j.issn.1001-9014.2023.01.012

2023-01-01

JOURNAL OF INFRARED AND MILLIMETER WAVES

Abstract:Photomultiplier tubes(PMT)have unique advantages in photon-counting LIDAR applications due to its photon-level sensitivity and lack of photon detection dead time. However,the output pulse height of PMT responds to the single photon follows the Gaussian random distribution,and there may produce pile up between different pulses. When using the fixed threshold method to identify the photo-events,the traditional single photon model can not accurately describe the photon detection process of PMT. By analyzing the influence of PMT output pulse height distribution,pulse pile up and the amplitude of photo-event discrimination threshold on the photo-events detection probability,a new PMT photon detection theoretical model was built,and the mode was simplified according to the practical application scene. The applicability of the simplified model was verified by Monte Carlo simulation. The correlation characteristics of the new model in photon-counting ranging are analyzed. A photon-counting LIDAR system is built,compared with Geiger mode APD,the PMT photon detection model has a slight loss of photon detection probability,but it has a smaller ranging walking error and higher ranging accuracy in photon-counting ranging applications. The experiment also proves that the new model is more consistent with the photo-event detection probability of PMT than the traditional single photon detection model. The new model has important guiding significance for the system design and theoretical analysis of PMT photon-counting LIDAR.
An Improved Mathematical Model for the Photon-Enhanced Thermionic Emission (PETE) Device with an Emphasis on the Photon-Electron Conservation Relationship

Tao Li,Tao Ma,Wen Wang,Gang Xiao

DOI: https://doi.org/10.1016/j.solmat.2024.112827

IF: 6.9

2024-01-01

Solar Energy Materials and Solar Cells

Abstract:Utilizing the quantum and thermal energy of solar photons simultaneously to realize broad solar spectrum utilization, photon-enhanced thermionic emission (PETE) exhibits high photoelectric conversion efficiency (PCE) potential, with maximum theoretical efficiencies of 47% under 3000 suns and exceeds the Shockley-Queisser limit for an ideal single-junction solar cell. Mathematical models have been proposed in the literature to investigate its operation laws and evaluate its power potential, while some did not consider the conservation relationship of photon-absorption and electron-emission comprehensively and their simulation results may deviate obviously from the actual situation. Herein, we develop both two zero-dimensional (0-D) and one-dimensional (1-D) models with the correction for the photon-electron conservation relationship based on the basic models of PETE. The results demonstrate that the modified models possess better predictions for the thermal current (emission electron flow from the cathode induced by heat). Moreover, the unreasonable negative values of quantum efficiency (QE) and photoelectron concentration can be eliminated at high temperatures. Based on the improved models, PETE shows a wider selection of cathode semiconductor materials since the cathode temperature is lower due to the larger thermal current. The maximum PCE of the 0-D model is 37% with 1.04 eV electron affinity and extremely high solar concentration ratios. For a practical silicon cathode PETE device, it is preferable to operate it under 50 suns in photon-enhanced thermionic regime and the maximum PCE is less than 4.5% due to silicon's poor photon absorption property.
An accurate semi-empirical model for PMT pulse signal analysis

Shuo Li,Xudong Lyu,Fei Wang,Chao Sun

DOI: https://doi.org/10.1371/journal.pone.0313999

IF: 3.7

2024-11-28

PLoS ONE

Abstract:The energy information of pulse signals is significantly important for applications such as computed tomography (CT), positron emission tomography (PET), and research on defects in condensed matter. Time-over-threshold (TOT) and multi-voltage threshold (MVT) are commonly used digitization methods in sampling pulse signal. However, both approaches rely on a mathematical model of the pulse signal to derive energy information. This study proposes a semi-empirical mathematical model for pulse signals formation process in scintillation crystal-coupled photomultiplier tube(PMT) probes, by utilizing the CR-RC shaping method. This mathematical model accurately describes output of the PMT pulse signals. This study analyzes a substantial dataset of pulse signals, comparing the performance of the newly designed mathematical model with that of the double exponential function in terms of their ability to fit pulse signals. The results indicate that the mathematical model developed herein achieves an average R 2 of 0.9255, significantly surpassing the 0.9155 of the double exponential function, thereby demonstrating its superior fitting efficacy.

multidisciplinary sciences
An analytical model for photomultiplier tube calibration

Leonidas N. Kalousis

DOI: https://doi.org/10.1016/j.nima.2023.168943

2024-01-01

Abstract:The purpose of the present article is to offer an analytical model that can be used for the calibration of photomultiplier tubes (PMTs). The derivation of the mathematical formulae is discussed extensively and we apply this machinery to a real problem; the gain determination of the R7081 Hamamatsu PMT. We hope that our work can provide a third, powerful alternative to the task of gain determination. We also believe that the techniques explained in this article can be applied to other problems in PMT calibration.

physics, particles & fields, nuclear,nuclear science & technology,instruments & instrumentation
Ranging Performance Model Considering the Pulse Pileup Effect for PMT-based Photon-Counting Lidars.

Zhiyu Zhang,Yue Ma,Song Li,Pufan Zhao,Yuyan Xiang,Xinyuan Liu,Wenhao Zhang

DOI: https://doi.org/10.1364/oe.386107

IF: 3.8

2020-01-01

Optics Express

Abstract:Currently, the ranging performance model for a photomultiplier tube (PMT)-based photon-counting lidar assumes the dead time is a fixed value for simplicity. This assumption introduces a bias in evaluating the ranging performance for a given PMT-based lidar because the dead time of PMTs is actually changeably caused by the pulse pileup effect. In this paper, the changeable dead time is calculated by a new empirical equation based on the Monte Carlo simulation. The empirical equation of the dead time is then used to derive the ranging performance model for PMT-based PC lidar systems. The proposed model is verified by an experimental lidar system equipped with a PMT and utilized to quantitatively analyze the influence of factors, such as the noise rate, discrimination threshold, signal intensity, and receiving pulse width. The result indicates that the receiving pulse width has a major influence, and when it exceeds 10 ns, the pulse pileup effect will introduce biases of more than 5 cm if the conventional model (ignoring the pulse pileup effect) is used. For a spaceborne lidar at an altitude of several hundred kilometers, the receiving pulse width will be significantly stretched when lasers illuminate on sloping surfaces, e.g., for a sloping surface larger than 2 degrees, so the effect of pulse pileup effect will have to be taken into consideration.
A New Compact Position-Sensitive PMT for Scintillation Detectors

S Nagai,M Watanabe,H Shimoi,H Liu,Y Yoshizawa

DOI: https://doi.org/10.1109/nssmic.1998.775131

IF: 1.703

1999-01-01

IEEE Transactions on Nuclear Science

Abstract:A new compact position-sensitive photomultiplier tube (PS-PMT), Hamamatsu R7600-C12, has been developed for scintillation detectors. The PS-PMT has 11 stages of metal channel dynodes and 6(X)+6(Y) crossed plate anodes in a 25.7 mm square/spl times/20 mm high metal can package, where the photo-sensitive area is 22 mm square. The performance of the PS-PMT was evaluated in terms of applicability to radiation imaging systems. In comparison with the former type of PS-PMT (Hamamatsu R5900-C8), the new PS-PMT provides smaller light spread and better position response. Also, by removing the flange at the bottom of the PS-PMT, the ratio of the effective area to the outward area is increased. The spatial resolution capability was demonstrated by imaging a stratified LSO array having an element of 1.8 mm/spl times/1.8 mm/spl times/10 mm. Each crystal element is clearly identified on the image map with 662 keV uniform gamma-ray irradiation. This paper describes the characteristics of the new PS-PMT and the experimental results for a gamma-ray imaging detector.
Restoring the saturation response of a PMT using pulse-shape and artificial-neural-networks

Hyun-Gi Lee,Jungsic Park

2023-07-11

Abstract:The linear response of a photomultiplier tube (PMT) is a required property for photon counting and reconstruction of the neutrino energy. The linearity valid region and the saturation response of PMT were investigated using a linear-alkyl-benzene (LAB)-based liquid scintillator. A correlation was observed between the two different saturation responses, with pulse-shape distortion and pulse-area decrease. The observed pulse-shape provides useful information for the estimation of the linearity region relative to the pulse-area. This correlation-based diagnosis allows an ${in}$-${situ}$ estimation of the linearity range, which was previously challenging. The measured correlation between the two saturation responses was employed to train an artificial-neural-network (ANN) to predict the decrease in pulse-area from the observed pulse-shape. The ANN-predicted pulse-area decrease enables the prediction of the ideal number of photoelectrons irrelevant to the saturation behavior. This pulse-shape-based machine learning technique offers a novel method for restoring the saturation response of PMTs.

Instrumentation and Detectors,Machine Learning,High Energy Physics - Experiment
A Statistical Non-Linear Model and Analysis for Photon-Level Photomultiplier Receiver.

Zhimeng Jiang,Chen Gong,Zhengyuan Xu

DOI: https://doi.org/10.1109/icc.2019.8761763

2019-01-01

Abstract:We characterize practical optical signal receiver in a wide range of signal intensity for optical wireless communication, from discrete pulse regime to continuous waveform regime. We first propose a statistical non-linear model based on photomultiplier tube (PMT) multi-stage amplification and Poisson channel, and then derive the optimal and tractable suboptimal duty cycle with peak-power constraint and average-power constraint for on-off key (OOK) modulation in the linear regime. Subsequently, a threshold-based classifier is proposed to distinguish three PMT working regimes based on the non-linear model. The performance of photon counting detection with optimal threshold for different sampling rates is evaluated from both theoretical and numerical perspectives. The proposed model can be adopted to select the optimal duty cycle and analyze the detection performance of PMT output signal in real applications.
A fluorescent lamp model based on its physical characteristics

Min Chen,Zhaoming Qian

DOI: https://doi.org/10.1109/PEDS.2003.1283132

2003-01-01

Abstract:Based on arc physics of fluorescent lamp, this paper developed a simple whereas comparatively accurate equation between lamp current and lamp impedance at high operating frequency. The proposed model has the advantages of simple form, easy derivation of model parameters, and good agreement with lamp responses in a wide lamp power range. This model can also simulate the ignition characteristics of the lamp. It will be a powerful tool for the design of high frequency electronic ballast of fluorescent lamp, especially in the dimming applications. The model is implemented in software Saber using Mast language, the simulation results appear to be in good agreement with the experimental data.
Exact solutions for silicon photomultipliers models and application to measurements

Enrico Junior Schioppa

DOI: https://doi.org/10.48550/arXiv.1710.11410

2017-10-31

Instrumentation and Detectors

Abstract:Dark count rate and correlated noise rate are among the main parameters that characterize silicon photomultipliers (SiPM). Typically, these parameters are evaluated by applying approximate formulas, or by fitting specific models, to the measured SiPM noise spectra. Here a novel approach is presented, where exact formulas are derived from a statistical model of dark counts and correlated noise generation. The method allows one to measure the true value of such parameters from the areas of just the first peaks in the dark spectrum. A numerical analysis shows the accuracy of the method.
Characterisation of the Temperature-dependent Dark Rate of Hamamatsu R7081-100 10" Photomultiplier Tubes

Steve T. Wilson,Samuel Fargher,Robert J. Foster,Matthew Malek,Matthew Needham,Andrew Scarff,Gary D. Smith

DOI: https://doi.org/10.1088/1748-0221/18/08/P08017

2023-11-27

Abstract:Dark noise is a dominant background in photomultiplier tubes (PMTs), which are commonly used in liquid-filled particle detectors for single-photon detection to see the results of particle interactions. A major contribution to dark noise is thermionic emission from the photocathode. The dark noise of Hamamatsu R7081-100 PMTs is characterised in a temperature and purity controlled water tank, with the thermionic emission contribution isolated. The results suggest that the intrinsic dark rate of PMTs does not depend on the medium, but does follow Richardson's law of thermionic emission. There are external contributions to the overall observed PMT count rate identified, but the intrinsic PMT dark rate in water matches that measured in air.

Instrumentation and Detectors,High Energy Physics - Experiment
A method for characterizing after-pulsing and dark noise of PMTs and SiPMs

A. Butcher,L. Doria,J. Monroe,F. Retiere,B. Smith,J. Walding

DOI: https://doi.org/10.1016/j.nima.2017.08.035

2017-08-22

Abstract:Photo-multiplier tubes (PMTs) and silicon photo-multipliers (SiPMs) are detectors sensitive to single photons that are widely used for the detection of scintillation and Cerenkov light in subatomic physics and medical imaging. This paper presents a method for characterizing two of the main noise sources that PMTs and SiPMs share: dark noise and correlated noise (after-pulsing). The proposed method allows for a model-independent measurement of the after-pulsing timing distribution and dark noise rate.

Instrumentation and Detectors
Comparison of Different Analytical Edge Spread Function Models for MTF Calculation Using Curve-Fitting

Tiecheng Li,Huajun Feng,Zhihai Xu,Xiaotong Li,Zhaofeng Cen,Qi Li

DOI: https://doi.org/10.1117/12.832793

2009-01-01

Abstract:The measurement of the modulation transfer function (MTF) is one of the key steps in characterizing the signal transfer characteristics of an imaging system as a function of spatial frequency in terms of linear response theory. Various methods have been proposed to determine the MTF of an imaging system which are based on point, slit or edge images. The slanted-edge method is the ISO 12233 standard for the MTF measurement of electronic still-picture cameras. In this paper, the method is modified to avoid amplifying the noise during the derivative computation by performing curve-fitting. In the experiments, we compare several different analytical function models for the ESF fitting and find that Logistic (Fermi) function gives the best result.
Photo-thermo-electric Modeling of Photon-Enhanced Thermionic Emission with Concentrated Solar Power

Hao Qiu,Haoran Xu,Mingjiang Ni,Gang Xiao

DOI: https://doi.org/10.1016/j.solmat.2022.111922

2022-01-01

Abstract:Photon-enhanced thermionic emission (PETE) is an advanced technology that combines both the photoelectric and the thermionic effects synergistically into a single device for direct electricity generation. However, its industrial-level application is still missing partly due to the lack of advanced models to analyze its operating characteristics and to understand the synergistic mechanism. Herein, we develop a numerical model of PETE by fully considering the optical, the electrical and the thermodynamic aspects with one-dimensional steady-state continuity equations of carriers in the semiconductor cathode. A hybrid PETE-Stirling cycle system is also pro-posed to yield an output power density of 162.65 kW/m2 with 32.8% conversion efficiency. The PETE conversion efficiency keeps similar to 20% with the optimal electron affinity increases from 0.5 to 1.14 eV as solar concentration ratio varies from 100 to 500. The cathode thickness should be optimized by considering both solar absorption and photon enhancement, where the thickness range of 0.78-1.52 mu m is obtained for 50-500 suns. The inter -electrode gap is also found to significantly affect the PETE performance by regulating both the space-charge effect and near-field radiation, where the range of 0.5-2 mu m is recommended. This work can serve as a foun-dation to understand the working mechanism of PETE converters and provide guidelines for the performance evaluation.
Advanced Back-Illuminated Silicon Photomultipliers With Surrounding P+ Trench

Haifan Hu,Ying Wang,Penghao Liu,Xiubo Qin,Junpeng Fang,Hongming Zhao,Zhe Ma,Jiatong Wei

DOI: https://doi.org/10.1109/jsen.2022.3188692

IF: 4.3

2022-08-15

IEEE Sensors Journal

Abstract:This study conducted the TCAD simulation of an advanced back-illuminated silicon photomultipliers (BI-SiPM) device. This BI-SiPM structure with pixels was surrounded by a p+ trench, which conducted the p+ implant region available on the surface toward the back side. The removal of the metal layer from the incident SiPM surface reduced the blocking of incident light and improved the fill factor of single pixels. Therefore, the photon detection efficiency of BI-SiPM was improved to approximately 70% when the bias voltage was 5 V. The TCAD device simulations were performed to study this BI-SiPM structure, and the quenching process based on Mixedmode emulator was investigated to introduce the BI-SiPM pixel structure into a SPICE circuit. The results indicated that the proposed design could improve the uniform distribution of the electric field and avalanche triggering probability on a photon illuminating surface and increase FF, without affecting the crosstalk between pixels. Moreover, the design consideration of manufacturing process flow for BI-SiPM was proposed.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
A performance evaluation system for photomultiplier tubes

J. Xia,S. Qian,W. Wang,Z. Ning,Y. Cheng,Z. Wang,X. Li,M. Qi,Y. Heng,S. Liu,X. Lei

DOI: https://doi.org/10.1088/1748-0221/10/03/p03023

2015-03-23

Journal of Instrumentation

Abstract:A comprehensive performance evaluation system for Photomultiplier tubes has been built up. The system is able to review diverse cathode and anode properties for PMTs with different sizes and dimensions. Relative and direct methods were developed for the quantum efficiency measurement and the results are consistent with each other. Two-dimensional and three-dimensional scanning platforms were built to test both the cathode and anode uniformity for either the plane type or spherical type photocathode. A Flash Analog-to-Digital Convertor module is utilized to achieve high speed waveforms sampling. The entire system is highly automatic and flexible. Details of the system and some typical experimental results are presented in this paper.

instruments & instrumentation
Non-empirical peak shape methods based on the physical model of the one trap one recombination center model

George Kitis,Claudio Furetta

DOI: https://doi.org/10.1016/j.apradiso.2024.111463

2024-08-03

Abstract:Any experimental Thermoluminescent (TL) glow-peak contains the activation energy information of its corresponding energy level within the band gap in insulating materials. The theory of peak shape methods (PSM) correlates the macroscopic geometrical characteristics of a single TL peak with activation energy of the level responsible for the TL peak by assuming that the area under a TL peak can be approximated by the area of a triangle. In this way the geometrical characteristics becomes the measure of the activation energy. In the present work new PSM expressions are derived, which are not empirical as the existing ones but are based of the physical model of one trap one recombination (OTOR) center. Three cases are considered. (I) Delocalized OTOR for re-trapping probability smaller than the recombination probability. (II) Delocalized OTOR for re-trapping probability greater than recombination probability. (III) Localized transitions OTOR model. The system of differential equations of each case model were solved analytically using the Lambert W function (or equivalently the Wright ω function). Then the resulted analytical expressions of TL intensity as a function of temperature were used to derive new PSM. The new PSM from all cases are formally exactly the same, having, however, strong differentiation in their coefficients. The functionality of the new expressions is tested and its comparison with pre-existing PSM is performed.
Lifetime-Extended MCP-PMT

T.Jinno,T.Mori,T.Ohshima,Y.Arita,K.Inami,T.Ihara,H.Nishizawa,T.Sasaki

DOI: https://doi.org/10.1016/j.nima.2010.10.145

2010-10-06

Abstract:In order to develop a long-lifetime MCP-PMT under high rates of circumstance, we investigated the degradation of the quantum efficiency (QE) of PMT's with a multialkali photocathode. We found that not only positive ions, but also neutral residual gases would damage the photocathode resulting in an enhancement of the work function; their countermeasures were established in newly manufactured square-shaped MCP-PMT's with 4 or 4x4 multi-anodes. The performances of the PMT's were measured: QE was stable up to an integrated amount of anode output charge of 2-3 C/cm^2, while keeping other basic performances steady, such as the time resolution for single photons of ~40 ps, a photoelectron collection efficiency (CE) of 60%, a multiplication gain (G) of a few x 10^6, and dark counts of 20-300 Hz. The causes of QE degradation are discussed.

Instrumentation and Detectors
Afterpulsing in Silicon Photomultipliers: Impact on the Photodetectors Characterization

Adam Para

DOI: https://doi.org/10.48550/arXiv.1503.01525

2015-03-05

Instrumentation and Detectors

Abstract:Novel generation of silicon-based photodetectors are attractive alternatives to the traditional phototubes. They offer significant advantages but they present new challenges too. Presence of afterpulses may affect many characteristics of the photodetectors. Simple statistical model of afterpulsing is used to evaluate the contribution to the observed dark count rates, to examine the contribution to the pulse height resolution and to demonstrate the modification of the observed timing properties of the SiPMs.

Simplified PMT Model

The Photon Detection Mode of Photomultiplier Tubes Considering the Pulse Height Distribution

An Improved Mathematical Model for the Photon-Enhanced Thermionic Emission (PETE) Device with an Emphasis on the Photon-Electron Conservation Relationship

An accurate semi-empirical model for PMT pulse signal analysis

An analytical model for photomultiplier tube calibration

Ranging Performance Model Considering the Pulse Pileup Effect for PMT-based Photon-Counting Lidars.

A New Compact Position-Sensitive PMT for Scintillation Detectors

Restoring the saturation response of a PMT using pulse-shape and artificial-neural-networks

A Statistical Non-Linear Model and Analysis for Photon-Level Photomultiplier Receiver.

A fluorescent lamp model based on its physical characteristics

Exact solutions for silicon photomultipliers models and application to measurements

Characterisation of the Temperature-dependent Dark Rate of Hamamatsu R7081-100 10" Photomultiplier Tubes

A method for characterizing after-pulsing and dark noise of PMTs and SiPMs

Comparison of Different Analytical Edge Spread Function Models for MTF Calculation Using Curve-Fitting

Photo-thermo-electric Modeling of Photon-Enhanced Thermionic Emission with Concentrated Solar Power

Advanced Back-Illuminated Silicon Photomultipliers With Surrounding P+ Trench

A performance evaluation system for photomultiplier tubes

Non-empirical peak shape methods based on the physical model of the one trap one recombination center model

Lifetime-Extended MCP-PMT

Afterpulsing in Silicon Photomultipliers: Impact on the Photodetectors Characterization