Optimal operation of transition-edge sensors on ballistic membranes

T. Kühn,I. J. Maasilta

DOI: https://doi.org/10.48550/arXiv.cond-mat/0702542

2007-02-23

Abstract:We calculate the operating parameters of a transition edge sensor that is mounted on a thin dielectric membrane with the assumption that the phononic heat transport in the membrane is ballistic. Our treatment uses the correct phonon modes from elasticity theory (Lamb-modes), and spans the transition from 3D to 2D behavior. The phonon cooling power and conductance have a global minimum as function of membrane thickness, which leads to an optimal value for the membrane thickness with respect to noise equivalent power at a fixed operating temperature. The energy resolution of a calorimeter will not be affected strongly, but, somewhat counterintuitively, the effective time constant can be reduced by decreasing the membrane thickness in the 2D limit.

Mesoscale and Nanoscale Physics,Superconductivity

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to optimize the operating parameters of Transition Edge Sensors (TES) on thin dielectric films, especially when considering phonon transport as ballistic. Specifically, the paper focuses on the following aspects:

1. **Minimum of phonon cooling power and thermal conductivity**: By calculating the influence of films with different thicknesses on phonon cooling power and thermal conductivity, it is found that there is a global minimum at a certain value of film thickness. This phenomenon also leads to a minimum in the Noise - Equivalent Power (NEP), thus defining an optimal film thickness.

2. **Maximum of the effective time constant**: When the film thickness is close to the optimal value, the effective time constant (\(\tau_{\text{eff}}\)) will reach its maximum. Therefore, when choosing the film thickness, it is necessary to balance the relationship between sensitivity and response time.

3. **Influence on energy resolution**: The influence of the thin film on the energy resolution (\(\Delta E_{\text{FWHM}}\)) of the TES calorimeter was studied. It was found that in the case of high loop gain, the energy resolution has a minimum at certain temperature ratios, and for higher temperature ratios, a thinner film can slightly improve the energy resolution.

### Formula summary

- **Total heat dissipation power \(P\)**:
\[
P=\frac{l}{2\pi^{2}}\sum_{\sigma,m}\int_{0}^{\infty}dk_{\parallel}k_{\parallel}\hbar\omega_{\sigma,m}\left|\frac{\partial\omega_{\sigma,m}}{\partial k_{\parallel}}\right|n(\omega,T)
\]
where \(l\) is the perimeter of the detector, \(n(\omega,T)\) is the Bose - Einstein distribution function, and \(\sigma\) and \(m\) are the indices of mode and branch respectively.

- **Heat dissipation power in two - dimensional limit \(P_{2D}\)**:
\[
P_{2D}=\frac{l\hbar}{2\pi^{2}}\left[\left(\frac{1}{c_{t}}+\frac{1}{c_{s}}\right)\Gamma(3)\zeta(3)\left(\frac{k_{B}T}{\hbar}\right)^{3}+\sqrt{2m^{*}}\frac{\Gamma(5/2)}{\hbar}\zeta(5/2)\left(\frac{k_{B}T}{\hbar}\right)^{5/2}\right]
\]

- **Heat dissipation power in three - dimensional limit \(P_{3D}\)**:
\[
P_{3D}=\frac{\pi^{2}ld\hbar}{120}\left(\frac{2}{c_{t}^{2}}+\frac{1}{c_{l}^{2}}\right)\left(\frac{k_{B}T}{\hbar}\right)^{4}
\]

- **Noise - Equivalent Power \(\text{NEP}\)**:
\[
\text{NEP}=\sqrt{2k_{B}\left[T_{D}^{2}g(T_{D})+T_{S}^{2}g(T_{S})\right]}
\]

- **Effective time constant \(\tau_{\text{eff}}\)**:
\[
\tau_{\text{eff}}=\frac{C_{el}}{g(T_{D})+\alpha\frac{P_{\text{net}}}{T_{D}}}
\]
where \(C_{el}=\gamma VT_{D}\) is the electronic heat capacity, \(\alpha = \frac{T}{...}\)