Abstract:The significant characteristics of the nickel-based Inconel 718 (IN718) superalloy are high strength, fatigue capacity, rupture strength, corrosion resistance, and creep resistance at temperatures exceeding 650 °C, which opens the application of IN718 for aircraft parts. The mechanical properties and surface residual stress (SRS) of the IN718 superalloy have been affected by fabrication and post-processing procedures, which shorten the service life of components. For the fabrication of complex aviation components, additive manufacturing of aerospace materials like IN718 has opened up new production techniques. However, localized melting and solidification produce anisotropy microstructure and a crystallographic texture with substantial tensile residual stress. These are responsible for mechanical anisotropy and pose metrological challenges for diffraction-based SRS detection. Knowing the magnitude and nature of SRS is crucial since they affect a mechanical properties and life of the parts. In this study, IN718 alloys were fabricated using the laser-based powder bed fusion (L-PBF) technique, and the impact of the standard ageing heat treatment (SAHT) process was assessed. The as-fabricated (AF) IN718 microstructure was found to have columnar dendritic structure and Laves phases in the interdendritic regions along the build direction. The SAHT sample microstructure led to the homogeneous precipitation of γ ′ and γ ′′ strengthening phases with δ and brittle Laves phases in grain boundaries. The average grain size of 41.56 μm in AF samples was increased to 44.80 μm after SAHT. The reduction of dislocation movements resulted in converting low angle grain boundaries found in the AF sample to high angle grain boundaries. SAHT samples displayed cubical texture along the and directions in the (001) plane. Following SAHT, there were increases in yield and ultimate tensile strength of 26.44% and 44.74%, respectively. On the other hand, the degree of elongation decreased to 36.19%. TRS in AF samples was converted into compressive surface residual stress following SAHT due to the phase transition. The process–structure–property relationship and the impacts of SAHT on the mechanical characteristics of the IN718 produced by L-PBF have been improved upon through this study.

Solidification Modeling of Alloy 718 Structural Castings

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Application of Confocal Scanning Laser Microscope in Studying Solidification Behavior of Alloy 718

Effect of Mold Dwell Time on Shrinkage Defects in Investment Casting of Superalloy Turbine Blade

Improving the Reliability of a Punched Casting from a Liquid Alloy by Process Mode Control

The Effects of Microstructure and Microtexture Generated During Solidification on Deformation Micromechanism in IN713C Nickel-Based Superalloy

Additive Manufacturing of Alloy 718 via Electron Beam Melting: Effect of Post-Treatment on the Microstructure and the Mechanical Properties

Microstructure simulation in pressurized solidification during squeeze casting of aluminum alloy A356

Semi-solid plasticity and deformation control of superalloy investment casting

Simulation of Fine Grain Casting Process of Superalloy K4202 by Thermal Control Method

Numerical Simulation and Experimental Casting of Nickel-Based Single-Crystal Superalloys by HRS and LMC Directional Solidification Processes

Models for casting solidification of Mg-9Al alloy

An Efficient Analytical Model for Predicting the Microstructure Characteristic Parameters of the As-Cast and Solid-Solution Treated Mg-Gd-Y-Zr Cast Alloys

Multi-scale Modeling of Solidification Process of Ni-based Superalloy Investment Castings

Experiment and Numerical Simulation of Microstructure of ZL114A Alloy in Low Pressure Casting

Analysis of Microporosity-Dependent Fatigue Crack Behavior in Alloy 718 by Using Synchronic Radiation X-Ray CT and FEM

Modeling of Investment Casting of Ti48Al48Cr2Nb2 (at%) Alloy Air Rudder Skeleton

Solidification and Segregation Behaviors of Superalloy IN718 at a Slow Cooling Rate

Macro and Micro Modeling on Conventional and Unidirectionally Solidified Investment Castings

Investigations on microstructure, crystallographic texture evolution, residual stress and mechanical properties of additive manufactured nickel-based superalloy for aerospace applications: role of industrial ageing heat treatment

3D Modeling of the Solidification Structure Evolution and of the Inter Layer/Track Voids Formation in Metallic Alloys Processed by Powder Bed Fusion Additive Manufacturing