Abstract:External reactor vessel cooling (ERVC) is one of the important severe accident mitigation strategies to achieve in-vessel retention(IVR) of melt core debris under severe accident conditions. Referring to the IVR-ERVC conditions for the prototypical pressure vessel lower head wall of elliptic-shaped, a critical heat flux (CHF) test campaign was, in the paper, carried out upon a full-sized thick test block section which was installed in a one-dimensional full height natural circulation test loop. Eighteen groups of heating rods with independent power control were inserted into the test block. Eight experimental measuring points were evenly distributed on the heating wall of the test block along the inclination angle, and the heating power shapes of each experimental measuring point were determined according to the Theofanous’ power shaping principle. Thermocouples were arranged near the heating wall and on all sides of the test block to obtain the temperature information during heating and CHF occurring. CHF data as well as their distribution along ellipticalshaped outer wall of test block were obtained. Meanwhile, preliminary evidence of typical CHF triggering mechanism on downwardfacing curved heating wall was deduced through the visual observations during the test. The visual observations show that when the evaporative drying area of the liquid film under the vapor block is large enough, it is difficult to cool the heating wall of test block. The wall temperature rises rapidly, and CHF occurs. Furthermore, effects of inlet subcooling, flooding water level, flow resistance and natural circulation flow rate, as well as the gap size of ERVC channels on CHF limits are experimentally studied. Test results show that, CHF increases with the increase of the inclination angle of heating wall, the increase of inlet subcooling can significantly increase CHF. Increasing the inlet subcooling can reduce the liquid temperature in the twophase boundary layer and effectively delay the evaporation of the liquid film, so as to improve the CHF. In the base cases and inlet subcooling cases, the relative decrease of CHF occurs in the uppermost section of the heating wall, which is called “exit phenomenon”. The CHF of the heating wall increases slightly with the increase of liquid level. While the change of natural circulation flow resistance and flow rate in a certain range has a rather limited impact on CHF. According to the CHF triggering mechanism, the flow rate change is not large enough to cause the instability and fracture of vapor block and the near wall flow structure does not change significantly, so the impact is limited. The influence of the change of gap size of ERVC channel on CHF is quite complicated. It seems that the relative relationship between the gap size and the thickness of twophase boundary layer, as well as the streamline constraints of the flow channel wall on the vapor phase both have influence on the CHF quantity and distribution.

Effect of different blister heights and forms on the void fraction distribution under subcooled boiling in narrow rectangular channel

Study on Flow Boiling Characteristics in Rectangle Channel After Formation of Blisters

Flow and Heat Transfer Characteristics in Plate-Type Fuel Channels after Formation of Blisters on Fuel Elements

CFD Analysis on Subcooled Boiling Phenomena in PWR Coolant Channel

A comprehensive analysis of the gap size influence on boiling crisis in narrow rectangular channels

Mechanism Study and Numerical Simulation on Blistering of Plate-Type Fuel

Numerical simulation prediction of critical heat flux for 5 × 5 rod bundle with multiple grid spacers and different cladding materials

Numerical investigation of critical heat flux during subcooled flow boiling in a vertical rectangular Mini-channel

Flow boiling heat transfer and pressure fluctuation characteristics in a divergent channel with inclined downward-facing heater

Numerical Investigation on Boiling Crisis in a Full-Length 5 × 5 Fuel Assembly under Typical Pressurized Water Reactor Conditions

Experimental study of two-phase parameters of subcooled boiling flow in a single-side heated rectangular channel

A Theoretical CHF Model for Downward Facing Surfaces and Gaps under Saturated Boiling

Experimental and Mechanical Research on Chf Characteristics During Combined/Bottom Quenching in Narrow Rectangular Channel

Numerical Simulation of Blistering Behavior in UMo/Zr Monolithic Fuel Plate

Numerical Investigation of Flow and Heat Transfer Characteristics in Plate-Type Fuel Channels of IAEA MTR Based on OpenFOAM

Experimental investigation and a mechanical model of critical heat flux in a narrow rectangular channel

Separate factors’ effects on CHF for flow boiling in an inclined rectangular channel under low mass flux

Experimental Investigation on CHF along Elliptic-shaped Lower Head Wall and Influencing Factor under IVR-ERVC Condition

On Void Fraction Distribution During Two-Phase Boiling Flow Instability

Numerical Analysis on Subcooled Boiling in PWR Coolant Channel Based on a Modified Multi-Scale Interface Model

Theoretical model for subcooled upward flow boiling heat transfer and critical heat flux for an inclined downward heated surface