Achievement of 35 MV/m in the Superconducting Nine-Cell Cavities for TESLA

L. Lilje,E. Kako,D. Kostin,A. Matheisen,W.-D. Moeller,D. Proch,D. Reschke,K. Saito,P. Schmueser,S. Simrock,T. Suzuki,K. Twarowski
DOI: https://doi.org/10.1016/j.nima.2004.01.045
2004-02-24
Abstract:The Tera Electronvolt Superconducting Linear Accelerator TESLA is the only linear electron-positron collider project based on superconductor technology for particle acceleration. In the first stage with 500 GeV center-of-mass energy an accelerating field of 23.4 MV/m is needed in the superconducting niobium cavities which are operated at a temperature of 2 K and a quality factor Q0 of 10 to the 10. This performance has been reliably achieved in the cavities of the TESLA Test Facility (TTF) accelerator. The upgrade of TESLA to 800 GeV requires accelerating gradients of 35 MV/m. Using an improved cavity treatment by electrolytic polishing it has been possible to raise the gradient to 35 - 43 MV/m in single cell resonators. Here we report on the successful transfer of the electropolishing technique to multi-cell cavities. Presently four nine-cell cavities have achieved 35 MV/m, and a fifth cavity could be excited to 39 MV/m. In two high-power tests it could be verified that EP-cavities preserve their excellent performance after welding into the helium cryostat and assembly of the high-power coupler. One cavity has been operated for 1100 hours at the TESLA-800 gradient of 35 MV/m and 57 hours at 36 MV/m without loss in performance.
Accelerator Physics
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to increase the accelerating gradient of superconducting RF cavities in high - energy accelerators to meet the requirements of future linear colliders (such as the TESLA project). Specifically, the paper aims to improve the accelerating gradient of the 9 - cell superconducting cavity from 23.4 MV/m to 35 MV/m or higher through the improved electropolishing technology (Electropolishing, EP), thereby providing technical support for the TESLA - 800 upgrade plan. ### Background and Problem Description of the Paper 1. **Requirements of Linear Colliders**: - Electron - positron colliders have played an important role in the discovery of new quarks and leptons and in verifying the standard model. - High - energy circular colliders cannot reach the TeV - level center - of - mass energy due to excessive synchrotron radiation losses. Therefore, linear colliders become the only viable option. - The goal of the TESLA project is to realize a superconducting - technology - based linear collider, with an initial design of the center - of - mass energy of 500 GeV (TESLA - 500) and an upgrade to 800 GeV (TESLA - 800) in the later stage. 2. **Existing Technological Bottlenecks**: - The niobium - made superconducting cavities used in the TESLA - 500 design need to reach an accelerating field strength of 23.4 MV/m. - The traditional buffered chemical polishing (BCP) process can only increase the accelerating gradient of multi - cell cavities to about 30 MV/m, far below the physical limit (about 45 MV/m). - The physical limit is determined by the critical magnetic field of the superconductor. For type II superconductor niobium, the maximum allowed rf magnetic field is close to the thermodynamic critical field (190 mT at 2 K). 3. **Improvement Methods**: - In recent years, the electropolishing (EP) technology has made significant progress on single - cell cavities, achieving an accelerating gradient of 35 - 43 MV/m. - The focus of this paper is to successfully apply the EP technology to multi - cell cavities and verify its performance in practical applications. ### Research Objectives - **Increase the Accelerating Gradient**: Increase the accelerating gradient of the 9 - cell superconducting cavity to 35 MV/m or higher through the EP technology. - **Verify Long - term Stability**: Ensure that the cavities treated by EP maintain excellent performance during long - term operation. - **Reduce the Need for High - Temperature Annealing**: Explore whether the EP technology can avoid high - temperature annealing at 1400°C, simplify the manufacturing process and reduce costs. ### Main Achievements - Four 9 - cell cavities reached an accelerating gradient of 35 MV/m, and the quality factor \( Q_0\geq5\times 10^9 \). - One of the cavities reached an accelerating gradient of 39 MV/m. - In the high - power test, one cavity ran continuously for 1100 hours (at 35 MV/m) and 57 hours (at 36 MV/m) without performance degradation. Through these achievements, the paper proves the effectiveness and reliability of the EP technology in increasing the accelerating gradient of superconducting cavities, providing important technical support for future high - energy physics experiments.