Abstract:Aged maraging steels offer unique strength and toughness via the presence of finely dispersed precipitates, allowing the material to reach values of up to 2400 MPa in yield strength in the case of 18Ni350. However, when aging heat treatments above 550°C are conducted, simultaneous precipitation and austenite reversion can occur changing the mechanical behavior of the material. Although many studies related to the physical metallurgy of maraging steels have already been published, less attention has been given to a detailed understanding of the initial formation of austenite and its relationship with the precipitates. In this study, undeformed and cold rolled commercial 18Ni350 maraging steel samples were submitted to short aging heat treatments of 1800 s at 600, 650, and 700 °C. The influence of the initial microstructure on subsequent phase evolution was studied using in-situ synchrotron X-ray diffraction and final microstructural products using transmission electron microscopy and atom probe tomography. Results show that cold rolled samples did not present faster kinetics of transformation of reverted austenite as expected, but this condition presented austenite in a different morphology than the undeformed condition. However, cold rolling changed the morphology of reverted austenite from elongated (undeformed case) to equiaxed; and induced a higher density of smaller Ni 3 Ti and Fe 2 Mo precipitates, especially after low-temperature aging. Besides, the deformation extinguished retained austenite, which influenced the reverted austenite formation, concluding that the simple increase in dislocation density is not a unique and direct factor to increase the reverted austenite kinetics.

Ex-situ observation of ferrite grain growth behavior in a welded 9Cr-1Mo-V-Nb steel during aging at 740 °C

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Effect of N on the Precipitation Behaviours of the Reduced Activation Ferritic/martensitic Steel CLF-1 after Thermal Ageing

Effect of microstructural evolution on high-temperature strength of 9Cr-3W-3Co martensitic heat resistant steel under different aging conditions

Effect of Long-Term Thermal Aging on Microstructure Evolution and Creep Deformation Behavior of a Novel 11Cr-3W-3Co Martensite Ferritic Steel

Evolution of strengthening factors during long-term aging at 650 °C in advanced 10% Cr heat-resistant steel

Microstructural Evolution and Mechanical Properties of Ultrafine-Grained Ferritic-Martensitic Steel During Thermal Aging

Nucleation of W-Rich Laves Phase Nanoparticles in Tempered Martensite Ferritic Steel During Long-Term Aging at Elevated Temperature.

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

EFFECT OF THERMAL AGING TREATMENT ON MICROSTRUCTURE EVOLUTION AND MECHANICAL PROPERTIES DEVELOPMENT IN A NI-CR-MO-V WELD METAL

Microstructure and mechanical properties evolutions of 9Cr heat resistant steel deposited metals with different Si contents during 550 °C aging process

Effect of aging temperature on the austenite reversion and mechanical properties of a Fe–10Cr–10Ni cryogenic maraging steel

Ferritic Stainless Steels for High-Temperature Applications: Stabilization of the Microstructure by Solid State Precipitation of MX Carbonitrides

Difference in Recrystallization Behavior between Martensite and Deformed Ferrite

Microstructure evolution and mechanical behavior of Fe-Mn-Al-C low-density steel upon aging

In Situ Observation of the Grain Growth Behavior and Martensitic Transformation of Supercooled Austenite in NM500 Wear-Resistant Steel at Different Quenching Temperatures

Effect of Thermal Aging on Microstructural Evolution in Ferrite of Duplex Stainless Steel in Nuclear Power Plant Applications

Characterization and Numerical Simulation of Nucleation–growth–coarsening Kinetics of Precipitates in G115 Martensitic Heat Resistance Steel During Long-Term Aging

Effect of long-term aging on the low cycle fatigue behavior and microstructure of a 10% Cr martensitic steel with low nitrogen and high boron contents at 650 °C

Interpretation of microstructure evolution and mechanical properties under aging treatments of a Fe–24Mn-0.6C–2Al-0.6V austenitic steel for cryogenic application

Precipitation and reverted austenite formation in maraging 350 steel: competition or cooperation?