Abstract:The fracture toughness of pressure pipe steels is vital for their design and safe operation. Understanding the deterioration of the fracture toughness and the corresponding fracture mechanisms is instructive and meaningful for material selection and development. The elastic-plastic fracture toughness of 9% Cr steels aged at 873 K and 923 K from the initial state to 20000 h was investigated at ambient temperature and 873 K. The deterioration of the fracture toughness and the corresponding fracture mechanisms are discussed in detail. For 9% Cr steels, voids mainly initiated from primary inclusions such as silicides, sulfides, alumina and manganides in as-received state, while voids initiated from both primary inclusions and secondary particles such as the Laves phase after longterm aging. These voids grew and coalesced with neighboring voids and crack tips subsequently until ultimately fracture. After aging at 873 K, the fracture toughness values tested at 873 K decreased from the initial state to 3000 h and then increased to 10000 h. The peculiar deterioration of the fracture properties after 3000 h of aging at 873 K can be attributed to the high number density of Laves phase particles in the steels. It was found that the densely distributed hard Laves phase particles induced strain concentration at the interface between the Laves phase and the matrix under plane-strain tension condition and promoted nucleation of voids. It was suggested that the spatial distribution of the Laves phase played a significant role on the void formation. 9% Cr steels with a denser distribution of Laves phases brings about voids with shorter interspaces, which are more susceptible to coalesce into crack tip, resulting in lower fracture resistance. After aging at 923 K from 10000 h to 20000 h, the number density, size and volume fraction of precipitates, block size, misorientation angle and dislocation density remained almost constant. The slight increase in the fracture toughness from 10000 h to 20000 h can be mainly ascribed to the coarsening of the martensite lath in this stage.

Microstructure and mechanical properties evolutions of 9Cr heat resistant steel deposited metals with different Si contents during 550 °C aging process

Effect of Ni content on microstructure and mechanical properties evolutions of 9Cr high Si heat resistant steel deposited metals

DSI-based Studies of the Effects of High-temperature Aging on Local Mechanical Properties of HR3C/T92 Dissimilar Steel Welded Joint

Microstructure and Hardness Evolution During Isothermal Process at 700 °C for Fe–24Mn–0.7Si–1.0Al TWIP Steel

Effect of microstructural evolution on high-temperature strength of 9Cr-3W-3Co martensitic heat resistant steel under different aging conditions

Effect of Long-Term Thermal Aging on Microstructure Evolution and Creep Deformation Behavior of a Novel 11Cr-3W-3Co Martensite Ferritic Steel

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Effect of Long-Term Aging on the Microstructure Evolution and Fracture Mechanism of 9% Cr Steels

Investigation on Gradual Degradation of Mechanical Property and Microstructure in 9% Cr Heat-Resistant Steels Via Interrupted Creep Test

The Effect of Microstructure Evolution on the Mechanical Properties of Martensite Ferritic Steel During Long-Term Aging

Effect of heat treatment on microstructure and mechanical properties of S31042 austenite heat resistant steel

Impacts of Aging Treatments on the Microstructural Evolutions, Mechanical Properties and Strengthening Mechanism in 1Cr15ni36w3ti

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Microstructural stability of a 9Cr oxide dispersion strengthened alloy under thermal aging at high temperatures

Interpretation of microstructure evolution and mechanical properties under aging treatments of a Fe–24Mn-0.6C–2Al-0.6V austenitic steel for cryogenic application

Microstructure and Mechanical Properties of Cast Cu-15Ni-8Sn Alloy

Effects of Silicon Content and Tempering Temperature on the Microstructural Evolution and Mechanical Properties of HT-9 Steels

Evolution of Microstructure, Mechanical and Corrosion Properties of Fe–13Cr–4Al-1.5Nb Alloy Aged at 450 °C

Microstructural Evolution and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy During Heat Treatment

Microstructural Evolution and Mechanical Properties of Ultrafine-Grained Ferritic-Martensitic Steel During Thermal Aging

Microstructure and Property Evolution of Cu–9Ni–6Sn-xCr Alloys During Thermo-Mechanical Treatment Process